Anycubic Photon Printer Owners 造訪社團

原文網址 Paul Denny
2018-10-15 02:52:18

Hey everyone, when using i.e. Anycubic green, is it possible to clean and cure a print whilst keeping the crystal green clear finish? After clean and cure my prints are always cloudy. Still new to this and very curious. Thank you all.

翻譯年糕

原文網址 Craig Cooper
2018-10-15 02:51:10

Setting up my brand new Photon.

When I open the photon.photon test file in AnyCubic Photon Slicer, there is no model shown (there is only an LCD Viewer window that opens up) yet in the user manual it shows the cube model. Why is this?

翻譯年糕

原文網址 Douglas Rector
2018-10-15 01:21:18

Has anyone had success (or failure for that matter) mixing monocure flex with Anycubic or Nova3D resins? What ratios? I just want to print minis that the weapons don't snap off of when my clumsy friends pick them up.

翻譯年糕

原文網址 Peter Manks
2018-10-15 00:57:08

Supports failed but still printed.

翻譯年糕

原文網址 Jeffrey L. Deltano
2018-10-15 00:32:22

Hi All, Photon slicer question. I import an stl and set the orientation and height from the plate high enough to leave a nice gap to the plate. But when I go to supports and then add supports and bring it back to edit to slice, it is now much closer to the plate. How can I get it to stay higher after adding supports?

Thx

翻譯年糕

原文網址 Stefan Lukus
2018-10-14 23:33:41

Blown away by the detail in this little printer. Took a bit to dial it in (much thanks to the awesome community) but damn!

翻譯年糕

Sen Kun
2018-10-15 02:02:04

原文網址 Fabrice Lamidey
2018-10-14 22:50:47

Hi everyone,
After quite a few prints, my Photon does not work anymore :
- Power switch turns the LCD screen on properly
- USB is working, I can read the card's content
- No fan
- No possible movement on the z-axis
- no UV light on the LCD screen

I can "launch" a print, the proper printing screen appears but nothing else.

I reflashed the 1.0 firmware. Flash worked, no change in behavior.

Has anyone seen that behavior ? Faulty or disconnected power cable inside maybe ?

翻譯年糕

Mike Bauers
2018-10-14 23:21:46

Fabrice Lamidey
2018-10-14 23:23:47

John Gray
2018-10-14 23:33:29

Fabrice Lamidey
2018-10-14 23:47:48

Fabrice Lamidey
2018-10-15 21:15:17

Curtis Miller
2018-10-24 08:24:13

Vinicius Silva
2018-10-24 08:34:41

Fabrice Lamidey
2018-10-24 12:19:29

Fabrice Lamidey
2018-10-24 12:37:46

Curtis Miller
2018-10-24 19:10:39

Vinicius Silva
2018-10-24 22:49:21

Fabrice Lamidey
2018-10-27 20:11:32

Charles Ivanova
2018-12-23 13:35:40

Sen Kun
2018-12-23 17:00:26

Muhammad Hazim
2019-01-08 16:30:50

Sen Kun
2019-01-08 17:29:59

Justin Wiggins
2019-01-28 16:44:10

原文網址 Craig Mumberson
2018-10-14 20:35:12

3D Cat scan (not actually a cat..)

翻譯年糕

原文網址 Benjamin Matthews
2018-10-14 19:01:29

finally back up and running. the new screen from anycubic came with a glass protector already on and no backlight. thank the makers :-)

翻譯年糕

原文網址 Enric Roca Gruart
2018-10-14 18:58:07

Z-axis wobble? I think no.

All views are from the same piece. Photo 1, this piece is printed in this position and you can see horizontal lines. But photo 2 and 3, yo can see diagonal lines and this lines I think must be horizontal, not diagonal, if is x-axis wobble. Photo 4 is perfect. Really Z-axis problem? All the lines in the same distance. Slicer program problem? printer problem?

Anycubic grey, 0,05-12-6,5-80-8

翻譯年糕