• COSPLAY 3D 建模
  • #maker+t=market
  • 3D列印服務
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Martin Da Costa
2019-02-05 01:10:12

I am trying to use VoxelOps to erode a photon file but it keeps failing at 75% with "no such file or directory" The directory that I am trying to save to does exist. What am I doing wrong?

翻譯年糕

Christopher Botha
2019-02-05 01:14:04

Martin Da Costa
2019-02-05 01:17:21

Martin Da Costa
2019-02-05 01:28:23

Alexander Mihailov
2019-02-05 01:29:32

Alexander Mihailov
2019-02-05 01:30:50

Martin Da Costa
2019-02-05 01:34:41

Martin Da Costa
2019-02-05 01:38:40

Darren Tarbard
2019-02-05 04:57:19

Martin Da Costa
2019-02-05 15:56:19

Martin Da Costa
2019-02-05 16:13:16


原文網址 Martin Da Costa
2019-01-25 20:30:34

Having used my lashed up heater (See Photonsters on github for link) for a while and found it gave good, consistent prints, I decided that the time had come to integrate it more completely with the Photon.
I removed the superfluous extractor fan (Picture 1) and useless filter (Picture 2) from the back right hand corner of the print chamber and used the fan as a template for a cover plate. I cut a hole in the cover plate for the wires and fixed the heater fan to it using epoxy resin. A couple of important points: The heater fan needs to be fixed aligned to the front edge of the plate or you won’t get any fixing screws in. The heater fan must be blowing the hot air onto the back panel and not forward onto the vat. This is to avoid hot spots on the vat and significant drafts on the print as it grows out of the vat.
Once the heater fan had been secured in position using the short screws liberated from the filter (Pictures 3 & 4), I fitted a 3-way connector block using one of the retained fan screws. The motherboard connector from the discarded extractor fan was liberated and new red/black twisted pair of wires used to connect to the block. The fan was connected to this supply and wires taken out from it through the back grill to power the thermostat. Make sure that the fan is connected red to +12V and black to 0V or it will run backwards! (Picture 5) The red heater wire was connected to the third point on the connector and a long red wire from it passed through the back grill. The black wire from the heater goes straight through the back grill.
A 2-way connector block was fitted to the back panel using the remaining extractor fan screw to replace one of the back grill fixing screws. One day I might replace this with a plug! The black wire from the heater went to one terminal and a red wire went from the other to the load connector on the thermostat, along with the red wire from the heater. The load wires and the thermostat supply wires were held in place with a strip of gaffer tape (Picture 7) with some slack at the top to allow for the hinge. Note that I now have a 12V thermostat and not the 220Vac one originally used. The thermostat unit is glued to the top. The sensor is passed through a hole in the side as shown in Picture 8.
So what happens? A 12V supply of at least 15A is attached to the 2 way connector for the heater. When the Photon is switched on, there is a short delay while the motherboard boots up. The circulating fan and thermostat are then switched on and the print bay is brought up to the selected working temperature.
Whilst I am happy with this, I do not take any responsibility for problems that others might have with their motherboard or other parts of the Photon by following my lead.

翻譯年糕

Martin Da Costa
2019-01-25 20:32:58

Martin Da Costa
2019-01-25 20:33:13

Martin Da Costa
2019-01-25 20:33:25

Martin Da Costa
2019-01-25 20:33:47

Martin Da Costa
2019-01-25 20:34:02

Martin Da Costa
2019-01-25 20:34:18

Martin Da Costa
2019-01-25 20:34:31

Martin Da Costa
2019-01-25 20:34:44

Martin Da Costa
2019-01-26 16:25:06

Martin Da Costa
2019-02-01 22:10:50


原文網址 Martin Da Costa
2019-01-17 23:06:17

Does anyone know what the drive capacity is of the motherboard on the socket that drives the print chamber extraction fan?

翻譯年糕

Jakob Martens
2019-01-17 23:20:46

Dustin Scott
2019-01-17 23:32:31

Martin Da Costa
2019-01-18 00:35:00

Martin Da Costa
2019-01-18 00:57:25

Sen Kun
2019-01-18 03:29:30

Martin Da Costa
2019-01-19 00:35:30


原文網址 Martin Da Costa
2019-01-09 20:21:05

Temperature is a recurring theme on these pages. When I got my second machine towards the end of last year, I decided to do a side by side comparison. My first machine had already been modified to incorporate temperature control in the print area (more later). I printed the same file on the two printers side by side at the same time. Room ambient temperature was 15C and in my modified machine the print area was at 27C. The print from the temperature controlled machine was definitely crisper and so I modified number 2.

On the top of each printer is a digital temperature controller with a sensor that can be seen to the right of the z slide in the picture. This controls a constant temperature PTC electric fan heater (12V 150W) that is stuck to the floor of the print chamber to the left of the z slide. The fan is always on to circulate the air and blows onto the back of the printer. A separate 12V 20A PSU drives the heating system for both machines. The extraction fan is disconnected so as not to suck out the warm air and the fumes that some find bothersome. I have the upper temperature set for 27C with 1C range. Delay typically takes the temperature down to 25.9C before rising to an overshoot of about 27.8C. This is air temperature and so the thermal mass of the VAT and resin smooths this out to probably just under 27C. The result is total consistency of prints and no discernable difference between the machines. All parts came from Amazon. From KKmoon 200-240V Digital temperature Controller thermocouple -40C to 120C with Sensor. With hind sight, I should have got the 12V model. From Kggy-eu Constant Temperature PTC Electric Fan Heater for Car Small Space Heating Incubator (12V 150W). Remove a mounting lug from this to allow it to be stuck to the base plate.. From LEDSONE LED Power Supply Unit 240Watts 12V 20A Constant Voltage DC. This is good for driving two heating systems.

翻譯年糕

Ben Tseng
2019-01-09 20:36:52

Martin Da Costa
2019-01-09 20:40:05

Thierry Vergé
2019-01-09 20:45:25

Alessio Petricciuolo
2019-01-09 21:54:41

陳彦廷
2019-01-10 00:34:12

Vinicius Silva
2019-01-10 00:42:26

Martin Da Costa
2019-01-10 01:13:17

Vinicius Silva
2019-01-10 01:17:05

Vinicius Silva
2019-01-10 01:18:26

Martin Da Costa
2019-01-10 01:30:21

Robert Silvers
2019-01-10 01:42:37

Vinicius Silva
2019-01-10 01:50:03

César Fernández
2019-01-10 16:46:40

Sen Kun
2019-01-10 17:40:03

Vinicius Silva
2019-01-10 18:34:34

Sen Kun
2019-01-10 18:38:00

Robert Silvers
2019-01-10 18:54:37

Martin Da Costa
2019-01-10 19:23:55

Vinicius Silva
2019-01-10 19:58:41

Martin Da Costa
2019-01-10 20:10:14

Holden8702
2019-01-10 20:41:52

Holden8702
2019-01-10 20:47:31

Vinicius Silva
2019-01-12 05:51:05

Calvin Hobbes
2019-01-16 09:00:29

Vinicius Silva
2019-01-16 10:18:29

Martin Da Costa
2019-01-16 17:59:29

Martin Da Costa
2019-01-16 18:04:34

Vinicius Silva
2019-01-16 18:52:26

Martin Da Costa
2019-01-16 19:47:38

Robert Silvers
2019-01-16 20:49:34

Vinicius Silva
2019-01-16 21:19:09

Vinicius Silva
2019-01-17 04:39:30

Richard Shapiro
2019-01-17 05:05:51

Robert Silvers
2019-01-17 05:10:11

Richard Shapiro
2019-01-17 05:26:42

Calvin Hobbes
2019-01-17 08:03:33

Calvin Hobbes
2019-01-17 08:13:42

Vinicius Silva
2019-01-17 08:14:22

Calvin Hobbes
2019-01-17 08:15:34

Vinicius Silva
2019-01-17 08:17:27

Calvin Hobbes
2019-01-17 08:18:53

Vinicius Silva
2019-01-17 08:21:54

Calvin Hobbes
2019-01-17 20:02:54

Vinicius Silva
2019-01-17 21:48:09

Martin Da Costa
2019-01-17 22:49:05

Martin Da Costa
2019-01-17 22:51:57

Richard Shapiro
2019-01-17 22:53:00

Martin Da Costa
2019-01-17 22:55:30

Richard Shapiro
2019-01-17 22:55:58

Martin Da Costa
2019-01-17 23:04:34

Richard Shapiro
2019-01-17 23:09:08

Richard Shapiro
2019-01-17 23:11:59

Calvin Hobbes
2019-01-18 02:29:12

Vinicius Silva
2019-01-18 02:57:43

Vinicius Silva
2019-01-18 02:58:21

Calvin Hobbes
2019-01-18 03:06:55

Vinicius Silva
2019-01-18 05:37:13

Vinicius Silva
2019-01-18 05:41:20

Calvin Hobbes
2019-01-18 06:32:37

Richard Shapiro
2019-01-19 01:32:10

Robert Silvers
2019-01-19 01:39:18

Richard Shapiro
2019-01-19 01:41:45

Martin Da Costa
2019-01-19 18:51:57

Richard Shapiro
2019-01-19 22:16:25

Vinicius Silva
2019-01-23 10:08:08

Calvin Hobbes
2019-01-23 11:32:51

Susan Sioux Mercer
2019-01-23 12:33:43

Susan Sioux Mercer
2019-01-23 12:49:28

Robert Silvers
2019-01-23 12:59:38

Martin Da Costa
2019-01-23 14:47:41

Robert Silvers
2019-01-23 14:51:18

Susan Sioux Mercer
2019-01-23 15:03:06

Kevin Reynolds
2019-01-26 08:53:49

Susan Sioux Mercer
2019-01-26 10:44:13

Martin Da Costa
2019-01-26 16:28:12

Susan Sioux Mercer
2019-01-26 16:48:04

Susan Sioux Mercer
2019-01-26 17:14:07

Martin Da Costa
2019-01-26 17:40:40

Robert Silvers
2019-01-31 11:05:39

Susan Sioux Mercer
2019-01-31 11:09:27

Martin Da Costa
2019-01-31 16:14:42

Vinicius Silva
2019-01-31 17:44:17

Robert Silvers
2019-01-31 20:17:45

Martin Da Costa
2019-01-31 21:38:41

Robert Silvers
2019-01-31 21:41:48

Martin Da Costa
2019-01-31 21:46:27

Robert Silvers
2019-01-31 21:53:21

Martin Da Costa
2019-01-31 21:54:52

Martin Da Costa
2019-02-01 22:22:08

Martin Da Costa
2019-02-01 22:23:00

Martin Da Costa
2019-02-01 22:23:09

Martin Da Costa
2019-02-01 22:23:22

Martin Da Costa
2019-02-01 22:23:35

Martin Da Costa
2019-02-01 22:23:45

Martin Da Costa
2019-02-01 22:24:05

Martin Da Costa
2019-02-01 22:24:16

Martin Da Costa
2019-02-01 22:24:24

Calvin Hobbes
2019-02-07 08:05:07

Vinicius Silva
2019-02-07 10:42:04

Ivan N. Potocnik
2019-06-05 00:39:04

Robert Silvers
2019-06-11 01:48:37

Petr Osipov
2019-11-06 22:35:22

Simon Wilson
2019-11-20 14:16:18

Harrie Kools
2020-01-30 23:16:43

Vinicius Silva
2020-01-31 00:02:30


原文網址 Martin Da Costa
2018-10-09 16:41:21

Had my Anycubic Photon for a few days now and what an improvement in print quality over my old B9 v1.1!! However, I've now tracked down a skew in the squareness off prints to the z-axis not being perpendicular to the LCD screen plate. Does anyone know of any adjustment or do I take it apart and shim the base of the z-rail?

翻譯年糕


 

討論主題

全不選 常用關鍵字