Anycubic Photon Printer Owners 造訪社團

原文網址 Leonardo Ferraro
2018-10-03 14:37:50

Hi, I am a new owner of a Photon.
Amy suggestions about how to optimize the standard settings in the slider to optimize the prints?
My first Benchy came a little with the lower part not so detailed...a little "melted" at first look.
Do you go with the standard settings?

翻譯年糕

Alex Vee
2018-10-03 15:40:46

Leonardo Ferraro
2018-10-03 16:23:32

Alex Vee
2018-10-03 16:26:56

Bahattin ManusH
2018-10-03 16:39:09

Leonardo Ferraro
2018-10-03 17:41:43

Sen Kun
2018-10-03 17:47:53

Leonardo Ferraro
2018-10-03 18:37:27

Alex Vee
2018-10-03 18:41:31

Robert Fliege
2018-10-03 20:14:41

Leonardo Ferraro
2018-10-03 20:53:42

Alex Vee
2018-10-03 20:58:00

原文網址 Willy Vallerian M
2018-10-03 12:42:48

Print this same object with diffrent rotation, left is 45deg, right is 0deg... Both showing same layer line on the surface which is supposed to be flat... My setting is 0.05 10 1 50 8 with anycubic green. Any sugestion to get rid this lines?

翻譯年糕

Sander Schonewille
2018-10-03 13:03:57

Willy Vallerian M
2018-10-03 13:13:44

Willy Vallerian M
2018-10-03 13:16:22

Wulf Freeman
2018-10-03 13:21:39

Willy Vallerian M
2018-10-03 13:34:25

Sterling Osment
2018-10-03 13:44:35

Willy Vallerian M
2018-10-03 13:45:52

Sterling Osment
2018-10-03 13:49:36

Stephen Wheeler
2018-10-03 14:04:06

Sterling Osment
2018-10-03 14:09:54

Sterling Osment
2018-10-03 14:11:00

Dana McDonald
2018-10-03 15:32:41

Trea Cotton
2018-10-03 18:22:28

Oliver Henne
2018-10-03 19:27:19

Willy Vallerian M
2018-10-03 20:30:01

Ilja Ilmar
2018-10-03 20:51:18

原文網址 Carlos Villamar
2018-10-03 12:22:08

Just got a photon, totally impressed. This was a small partial print with the Nova3D white resin (LT .05, NEXP 10, OT 6.5, BET 60, BL 8 )

翻譯年糕

原文網址 Matt Tilson
2018-10-03 12:21:15

Any ideas what would cause this to happen during curing after cleaning? I was curing two others just like this at the same time and they both came out fine.

翻譯年糕

原文網址 Andrew Stockton
2018-10-03 11:36:19

Original design! I'm very happy with the print, although now I see some things that need to be changed in the model. Printed in green and primed gunmetal gray.

翻譯年糕

原文網址 Adam Horton
2018-10-03 09:50:03

So...grinding noise when the motor is working. Happened suddenly mid-print. Ideas and solutions? So...grinding noise when the motor is working. Happened suddenly mid-print. Ideas and solutions? 翻譯年糕

Adam Horton
2018-10-03 14:09:27

Adam Horton
2018-10-03 14:09:46

Marco Zannini
2018-10-03 16:34:37

Ritmo Pat
2018-10-03 16:38:58

Marco Zannini
2018-10-03 16:39:37

Ritmo Pat
2018-10-03 16:40:46

Marco Zannini
2018-10-03 16:41:25

Ritmo Pat
2018-10-03 16:44:34

Marco Zannini
2018-10-03 16:44:39

Marco Zannini
2018-10-03 16:45:19

Ritmo Pat
2018-10-03 16:48:56

Marco Zannini
2018-10-03 16:50:25

Sen Kun
2018-10-03 17:11:15

Sen Kun
2018-10-03 17:12:38

Marco Zannini
2018-10-03 17:14:09

Ritmo Pat
2018-10-03 17:31:54

Luke Taylor
2018-10-03 18:01:30

Marco Zannini
2018-10-03 18:24:41

Kimmy Lemrick
2018-12-12 05:56:36

原文網址 Christopher Botha
2018-10-03 09:47:22

Tried to cast the Anycubic Maroon, mixed success.

翻譯年糕

原文網址 Javier Ignacio Romero Schmidt
2018-10-03 09:42:48

I have a question about the photon file editor. Is it possible to eliminate a complete piece from a photon file? I have a piece I need to print but it's together with another piece I already printed, I don't want to make the supports once again

翻譯年糕

原文網址 Cody Holland
2018-10-03 06:57:15

So I just filtered my resin from my second print, and I found a crisp rectangle of cured resin stuck to FEP sheet (which explains the chunk on one of my prints) but why did this happen?

翻譯年糕

原文網址 James Mcloughlin
2018-10-03 06:29:44

Not the best paint job (needs some clean up) but does the job

翻譯年糕

討論主題

發文排行榜

回文排行榜

熱門關鍵字