Anycubic Photon Printer Owners 造訪社團

原文網址 Peter Wal
2018-09-16 20:18:06

Hi, has anyone good settings for the Anycubic resin "Maroon"?

翻譯年糕

原文網址 Michael Kingsley
2018-09-16 20:00:45

Any advice would be greatly appreciated! (Sorry for the double post I couldn’t find the first one.)

My settings are:
Monocure Rapid 3D Clear
Layer - .05 Exptime - 14s O time - 1s BotExp - 90s - Layers - 10

My fep is new and everything is leveled. Z set per manual instructions with the paper snug. No obvious misalignments.

翻譯年糕

原文網址 Christopher Botha
2018-09-16 19:13:29

Finally got the build off the photon in one piece, appears it didn't like being in my garage and resin was quite thick.. warmed up the work area and seems to be better. Below is the same bed of rings, both printed at 30um, for easy identification, white was on the Phrozen (no AA on this build) and green was on the Photon.

I snapped 4 rings on the grey build which is why its shorter.. butter fingers.

All images raw from my camera. Hope FB does not ruin them. All up, tbh, there is not a huge difference, I feel like the Phrozen was a bit sharper, but then again, I think my green was a tad overexposed in my desperation to try get it to stop pulling off at the supports, not realizing it was a temperature thing....

I'm happy with both and if I was cleaning up I'd be happy to clean either as a casting, I'll cast some of the green resin tommorow to see how they look in metal, sadly the gray is not castable (yet). Those who are wondering can review both and decide for yourself.

翻譯年糕

原文網址 João Tomás Afonso
2018-09-16 19:11:04

Does anyone uses different kinds of lamps in the room your printer is?

翻譯年糕

原文網址 Andy Murtagh
2018-09-16 18:22:18

OK guys, being new to the 3d printing world, please give me your recommendations on the following:

1. Best modelling software
2. Best software for supports
3. Best slicer

Thanks in advance!

翻譯年糕

Liam Kaiser Wilhelm Smith
2018-09-16 18:38:13

William Bassett
2018-09-16 18:38:41

Adam Widdowson
2018-09-16 19:07:00

Puren Bulat
2018-09-16 22:42:35

Eddie Bianco
2018-09-16 23:37:51

Matt Tilson
2018-09-17 01:13:24

原文網址 Stephen Lewis
2018-09-16 18:02:55

Hey everyone! I just wanted to let you know that I am excited to be taking over MakerMarket.co and I have already put my first order into Monocure for inventory! As soon as I get that in and go over some of the finer points with Jordan, we should be back up and running!

翻譯年糕

Nel Elson
2018-09-17 06:56:20

Douglas Rector
2018-09-22 07:24:32

Stephen Lewis
2018-09-22 09:59:48

Douglas Rector
2018-09-23 00:25:33

原文網址 Charlie Anderson
2018-09-16 17:52:03

原文網址 陳彦廷
2018-09-16 17:11:03

Hollowing & keying a horse in meshmixer.

翻譯年糕

原文網址 Paweł Grochowski
2018-09-16 16:43:20

I make hexes for board game "Terraforming Mars". Resin Phroze ABS like gray.

翻譯年糕

原文網址 Ok Rimr
2018-09-16 16:43:06

Hi - freezing and restart of my Photon still persists. I am OK with that, but, it is really annoying. In future I will try check a Z motor driver voltage (last remaining think for check).

翻譯年糕