CR-7/8/10 3D Printer 研究社 造訪社團

圖片在這...

好帥阿

Nice Designed, Cheer!

來的真是剛好，昨天拿到跟團長訂購的線，拆封後一整個呆住，沒有東西架，只好剪一段下來用

趕快回家把箱子撿回來

立馬印來看看

這麼短一條39元不算便宜吧

電料行印象是10米，100多吧，看直徑價格不一。

吸管自己剪.不用花錢~哈

前幾天逛大創.看到也是差點下手~...(後來想想家裡吸管還有好多...就忍住了~...39也是錢啊~..哈)

吸管插到削鉛筆機裡就有了

疑~可以這樣切喔...

蠻好用的

诶? 我是用美工刀割吸管。然後第一條太軟，所以後來就割斜一點大概3:1

理線用的嗎?

原廠的網子需要安裝技巧..這種就簡單多了~

完全不用改機，只改參數嗎?

是的....我是機器白痴@@....我完全不會改機器. 都是用參數及調皮帶等方法來解決

用我之前說的極限皮帶固定法.應該可以輕鬆滿版才對啊~

嘉祥大~~~~~~我記的有分享. 但就是找不到@@

看來這個問題及嘉祥大的解決方法也要放到共筆系統中了. 很多人會需要!

平台的極限是165mm啊(煙

https://www.facebook.com/photo.php?fbid=1036641899710004&set=gm.1680394248858187&type=3&theater
換成我的自動調節皮帶導輪.可以再印大一些~(但就要變更韌體才行了)

謝謝嘉祥大~~~~~~~

Have u check the gear of excluder? Does it still move?

Shih-Wei Peng The problem parts, I found it happened at the high around 12-15 mm.

Some part I can print without any problem. Will print the pillar and see again.

Problem base on
1) The filament is stuck due to diameter
2) Something clog inside the nozzle head
3) Temperature not right , too hot melt and freeze inside the ptfe tube

Thanks Declan Cheng , I'll check on the 1st item first.
Anyway, If it clog inside nozzle, how to clean it? any recommend?

you welcome~~
For me will use a metal stick like 1.5mm and go through inside the nozzle head and squeezed all the material out~~~but have to watch out the pressure force preventing hurting the whole nozzle head and part, when u find out is hard to sque ezed out the material, using a tiny sewing needle pierce through the nozzle head with more careful preventing the needle head broke inside the nozzle head~~
This how i clean my nozzle when clog~~~is useful
Hope this help u~~~

but sometimes that happen due to the filament diameter to big , more than 1.9mm will stuck inside the ptfe tube~~~~
so u need to check the diameter of the filament...
base on the picture is more likely the diameter of the filament problem~~~

By the way ,check your retraction distance~~~

u can use this to clean the nozzle~
Carefully remove the nozzle, and use the hot air gun to clear clog.
ps: remove the nozzle must heating nozzle up to 190 degree，becus that might have some cooling material

Many thanks to Declan Cheng , ChienMing Liang
Now I under testing, seem like the filament diameter too big. I jsut cut it out for 4-5 meters and start run again. Let see how is going.

I am groot.

哇~~迷你~~請問他是誰?

目前我只印了四個輪子