ATOM 3D Printer Group 造訪社團

i don´t think the GCODE is the problem....the problem is the printer!

Mariel Diaz Castro Could you get the M503 result from the Pronterface?

SENDING:M503
echo:Steps per unit:
echo: M92 X160.00 Y160.00 Z160.00 E200.00
echo:Bed Level Matrix :
-2.694 -2.694 -2.694 -2.456 -2.263 -2.263 -2.263
-2.888 -2.888 -2.675 -2.481 -2.331 -2.306 -2.306
-2.925 -2.769 -2.631 -2.513 -2.406 -2.375 -2.506
-2.838 -2.725 -2.631 -2.556 -2.463 -2.463 -2.638
-2.713 -2.688 -2.631 -2.575 -2.556 -2.619 -2.750
-2.775 -2.775 -2.738 -2.688 -2.656 -2.700 -2.700
-2.969 -2.969 -2.969 -2.925 -2.838 -2.838 -2.838
echo:Maximum feedrates (mm/s):
echo: M203 X300.00 Y300.00 Z300.00 E300.00
echo:Maximum Acceleration (mm/s2):
echo: M201 X3000 Y3000 Z3000 E9000
echo:Acceleration: S=acceleration, T=retract acceleration
echo: M204 S9000.00 T9000.00
echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)
echo: M205 S0.00 T0.00 B20000 X20.00 Z20.00 E5.00
echo:Home offset (mm):
echo: M206 X0.00 Y0.00 Z0.00
echo:PID settings:
echo: M301 P16.54 I1.30 D52.56

looks fine to me, suggest to follow other inspection from another post.

I have change the 12V power supply for another one, it seems to work better by now...I am going to print more parts to see what happens. Thanks...very good technical support!

Please keep in contact with us, and let us know how the new power supply works with further printing tests

same problem.
Need to fix it.

It seems cause by Auto Leveling, you need check your Hub's endstop(z-probe).

It's not because of autolevelling

Only in this video the bed levelling its not correct....but the main problem are the motors and the extreme vibration that is not because of autoleveling it has to be another thing..last week the problem was with the lateral fans. Were not working...and this week the motors...need to solve this

Your hotend already hit the print plate. You need to check this.

And what about the vibrations?

Sorry,I have no clues about this. but did you try to apply some oil on linear guideway?

J'étais partant pour acheter cette...
Mais vu tous les problèmes qu'elle a !!!
A réfléchir

Mariel Diaz Castro How about try to use another 12V power supply?

Or
1. try to restore failsafe & save.
2. try to upload the fw again.

I had similar problems with my Atom2. Turns out the cause was a short in the motherboard that caused incorrect readings from the X & Y limit switches when they were closed together.To check for this use Pronterface to test each limit switch by itself (put printhead in the middle, then manyally close each limit switch), then check each pair of limit switches, and finally test all 3 at once (you need 3 hands to do this.)

挖賽 可以印到這麼漂亮喔

歡迎到我們粉絲頁板上按個讚喔~謝謝

But i can print this
umm... why?

Prime Pillar >Enabied

https://www.youtube.com/watch?v=9hKKqFM9KOc

Slow down the print speed or enable prime pillar function will help you cooling your model before printing the next layer. :)

After code very 20 .
I slow down printer speed to 15 mm/s and acceleration to 500 .
Reduces voltages to 6.50 v .
...
Not success

your models shows that cooling time isn't enough, causing undesirable warping, to counter this you can active the side fan function in kisslicer.

or you can cancel the wipe function.

The pixel star seen to be well .

I think part of the problem comes from AUTO level.
The two lines are not equal because the tiling base .
I will try to solve it.

I have the same problem..the star and the cube prints very cool...but its impossible to print the Eiffel Tower

I resliced the Eiffel_tower_mini (45mm height), reducing the Prime & Suck parameter to 6 mm, and the finished model's photo is attached below :)

gcode:
https://www.facebook.com/....../Eiffel_Tower_mini......

Thx god

請問有STL檔嗎? 我也印了一個。但沒這個漂亮。Thingiverse有看到一個像這樣的，但是它是用Inch為單位，我用KS轉成mm，就太大沒辦法印了....Orz.

https://grabcad.com/library/3d-printed-vr-headset-1

戴士偉 謝謝。我就是在thingiverse下載這個，結果他的檔案是用Inch為單位，用KS轉出來會太大。我不太會用3D tool，若有現成的STL檔會很感謝。

nice!

Excellent!

AWESOME!!

如果真的堵住的話應該會完全不出料，自己再檢查看看怎樣才會出現這種情形

這兩天我也遇到一樣的狀況，算是失步嗎?

參數1

參數2

（淚）～>_<～（握手）
我是覺得是啫料還是進料馬達有問題（有時會頻繁且快速的吐料又回抽，約快一秒二下）。我設定是官網抓的⋯

回抽速度不一定要照原廠設定，那個是參考用，進料馬達上的入料臂上的螺絲確記不要完全鎖緊

我的回抽設定

ㄜ~
要不要順便看一下~
是不是在"某個角度位置"~
卡到加熱的電線~!

Yier Fansder , 感謝！我明天重組噴頭總成那一部份看看。

如果，有壓到加熱線，面版上的溫度應該會掉下去才是。但，實際上，它「回神」時又是那麼突然好了⋯

我的清況不是壓到~
而是在某個角度的時候~
會接觸不良~
導致加熱不穩定~
至於面板上的溫度顯示~
我沒去注意~
因為~
我現在都是用usb連接~
用電腦去控制列印~
然後控制程式~
出現了低溫警告~
我才發現原來是電線問題~
而不是噴嘴塞住~!

hi Clarence Lee , 看來和溫度設定沒什麼關係（我直接用 g-code 檔輸出的），我的噴頭太容易堵了。只能送機器去給 Mark Chen 瞧瞧了⋯

回抽要調整

這個檔案目前是什麼參數切出來的呢？ Clarence Lee

看gcode前面有吧...
不過這不是啥值得參考的參數..
我的擠出機管長有縮短過...
我自己當時印到210就黏不住了..

把輸料的管子變短就好多了，直接用ATOM網站上的參數改加熱230度和推料速度60mm/s⋯（雖然ATOM變好醜⋯）

哈哈⋯希望不是曇花一現

翻過來看第一層⋯