ATOM 3D Printer Group 造訪社團

原文網址 許育財
2017-06-29 10:28:00

搞個Neutron, Proton大會師, 一定很壯觀

Kevin Lan
2017-06-29 21:49:35

這邊到底完成幾台Neutron, Proton了?
有人統計過嗎?

Estima Lin
2017-06-29 22:30:40

Neutron要改雙光軸，修改中...
Proton缺零件待料中...
所以都算沒完成～

原文網址 洪瑞良
2017-06-28 23:32:53

工商時間.已經版主同意.朋友有一台2.0要賣.但是有一點故障.我覺得應該是極限開關.但是他只要賣2萬3.需要的舉手一下(賣出)

原文網址 Bless Ma
2017-06-28 23:04:49

阿福柔頭的原型
訂製雨傘架

梁琄
2017-06-29 12:57:21

結果阿福柔的反應比傘架好 ? ?

原文網址 林雋哲
2017-06-28 15:49:58

想請問一下不同的主板電流輸出是否不一樣呢我發現neutron團購的ramps1.4+mega2560 加熱到200度還有點困難風扇也不夠力請問是主板問題嗎？

吳水豚
2017-06-28 15:56:57

變壓器有無調到110v

翟玉申
2017-06-28 16:08:53

我每次印風扇都強到我要趕快調弱耶，接線會不會用到比較細的而不是18awg

原文網址 陳卲玥
2017-06-28 15:47:31

哈囉大家！我是剛入門的新手，昨晚好不容意通過地獄自動測試，但發現在列印atom官網雙色測試模型，在切換料的時候會卡住，如圖白色料就卡住，灰色料正常，在列印單色就很正常，請問大家在出料上有沒有什麼該注意的技巧呢？感謝大家：）

黃俊傑
2017-06-28 15:49:11

先拆下來檢查吧！
http://imgur.com/a/NYcFm

尤博民
2017-06-28 23:53:34

問老巫

原文網址 Moko Jenson Huang
2017-06-28 12:59:45

MK3 - 0.2 NOZZEL
被我玩到慘不忍睹的噴頭
以前用六角板手桶+PLA去黏
通常都有效
.........
但這次卻沒用
只好用瓦斯爐火攻=>變黑金剛了
再用六角板手桶+PLA去黏
重複了十幾次
...........
還是完全擠不出@.@
雖然實在不想用0.2mm針頭去桶
但是還是買了
https://goo.gl/orMQhc
.........
這到貨大概也要十幾天
想到有一瓶ACETONE REMOVER
姑且一試吧
給他泡了一個星期
剛剛組裝加熱
真的擠得出來了
顆顆顆
https://goo.gl/FMcvnj

洪瑞宏
2017-06-28 13:08:29

http://goods.ruten.com.tw/item/show?21608861768698
通針可以考慮這家

ChihJun Soong
2017-06-28 13:59:26

我後來干脆買一支小噴火槍。

張不凡
2017-06-28 15:17:18

我

原文網址 Yinka Alade
2017-06-28 12:49:34

Question, why would a printer on my Atom 2.0 be perfectly fine with a layer height of 0.2 but when I got to 0.1 the print has gaps in the layers laid down? Also I've adjust the Z height and nothing really solves that problem. The main problem is the first layer which unfortunately for this print needs to be almost perfect.

翻譯年糕

Dennis Chen
2017-06-28 16:02:47

Maybe the print bed needs re-calibrating for 0.1 to work. You can run auto-leveling twice or more to ensure precision first, then fine tune the Z height.

Yinka Alade
2017-06-28 19:30:04

Tried that a bunch of times already and it still prints like its clogged or something when it's not.

Joe Abaquin Bing Aquino
2017-06-28 20:35:05

Maybe u over tighten the bracket one and the bed is a bit flexing

Yinka Alade
2017-06-28 21:41:11

Brackets are good. I doubt the bed is flexing because where it determines to be weird is inconsistent. It's mainly an issue with prints with large first layers.

So far I've done a .15 print that came out decent. It had a few errors on the first layer. Every layer after the first is fine.

Joe Abaquin Bing Aquino
2017-06-29 01:05:49

That's good to know. And if that happen to me again, I will do .15 too.

原文網址 Bless Ma
2017-06-28 08:32:00

刷一下存在感
阿福柔頭收成了