ATOM 3D Printer Group 造訪社團

原文網址 Vincent Liu
2017-01-25 11:05:20

各位先進，小弟又遇到問題了，cura無法切片，檔案是從proe轉成stl檔再load進來什麼都沒改，是不是我少做什麼步驟????

黃俊傑
2017-01-25 11:06:34

超出範圍了... 去機器設定那邊更改底面積

神塚雲
2017-01-25 11:11:14

要調整比例大小

Vincent Liu
2017-01-25 11:20:51

了解，去那邊改底面積

Vincent Liu
2017-01-25 14:20:31

Vincent Liu
2017-01-25 14:20:53

請問這樣是不是模型縮小了

Vincent Liu
2017-01-25 14:21:16

機器設定的底面積最大可以改多少?

原文網址 Memgyu Liao
2017-01-25 10:44:06

想請問列印的接合線有辦法自己決定在不明顯的地方嗎?

黃俊傑
2017-01-25 10:44:50

哪套切片阿？

Memgyu Liao
2017-01-25 10:47:15

CURA

原文網址 廖新弘
2017-01-25 09:20:41

轉貼有趣的陶笛，AutoCAD 出品
https://www.facebook.com/Autodesk.HongKong/videos/1175764432459371/

原文網址 邢鳳言
2017-01-25 04:56:38

一張A4紙剛好過又有磨擦到，我用厚薄規試的結果是0.05mm會過，0.06過不去，好準的A4紙，剛好是最小層高的厚度。
# 試印校正

陳順得
2017-01-25 08:39:51

其實測的應該是觸發行程，所以大家都有一點點不同

李穆
2017-01-25 09:23:18

那這樣就太低了，紙的磅數不夠XDDD。
Goto zero指令是把噴頭送到0.1mm高的位置（已含Z-offset）。
既然已經有厚薄規那就用0.1mm去測就好了

Hawke ChienSheng Liu
2017-01-25 09:41:43

A4紙要用80磅的。

原文網址 Birk Binnard
2017-01-25 03:58:45

Look what I found

My filament broke while I was changing it so I had to take the hotend apart to grab it from the other end. Since I had the hotend apart I thought I'd check the PTFE and it looked like this. So I replaced it. I guess it is worth checking this from time to time jsut to make sure it is OK,

Fortunately I have some 3/2 PTFE that fits my Ver. 2.0 hotend. I think I read somewhere that the Ver 2.5 version uses 4/2 PTFE which is much easier to purchase.

翻譯年糕

Yinka Alade
2017-01-25 05:25:00

One of the more annoying things.

Birk Binnard
2017-01-25 06:13:30

Indeed. After I got that out I discovered some melted/fused PLA stuck inside the nozzle. Tried getting it out with an unbent paper clip - that helped, but didn't do a complete job. So I reverted to the tried & true torch method - heating the nozzle w ith a propane torch until flames come out the back (signifiying vaporization of the fused PLA inside) and the metal color changes from red to blue. Then it's just a matter of reassembly.

Fortunately this time I was able to re-use the same thermistor.

原文網址 Birk Binnard
2017-01-25 01:41:11

More info on stepper motor motion smoothing

This last few posts on this Craftware forum thread

https://craftunique.com/forums/view-thread/2407

show a different/simple way to improve stepper motor motion: simply short out pins 18 & 19 on the stepper motor socket. Apparently this forces the stepper controller into "fast" mode which results in better hotend motion. Is there any chance this might work on Atom2.x machines?

翻譯年糕

原文網址 Rick Yang
2017-01-25 00:34:11

這棵也不錯用，圓圓的很討喜
http://www.thingiverse.com/thing:1837493

James Lin
2017-01-25 00:57:39

感謝，正在找旋鈕 ~

原文網址 Jean-François Larbre
2017-01-25 00:21:31

Hello,
In the Firmware of ATOM 2.0 (v2.0.7), when the files contained on the SD card are listed and the name of the files is too long for the LCD display, there is no automatic scrolling While on other RepRap yes.
Is it possible to remedy this problem ?

翻譯年糕

原文網址 邢鳳言
2017-01-25 00:15:40

感謝賴昊君（Kevin Lai）指導使我不用再狂插猛送手指痛痛，使用前請先關掉步進馬達！單雙色圖檔都在此 http://www.thingiverse.com/thing:2058018
# 擠料旋鈕
 # 試印校正