ATOM 3D Printer Group 造訪社團

原文網址 Dan Salvador
2015-12-28 22:45:50

i was wandering where do you guys buy the 3M blue tape and what serial number of it (i use 2093EL) , it's really overpriced in my country

翻譯年糕

陳奕丞
2015-12-28 22:47:30

2090~

Dan Salvador
2015-12-28 22:48:41

do you buy it online ?

徐凡
2015-12-28 22:50:13

I bought it in Supermarket. And we an also buy it online.

陳奕丞
2015-12-28 22:50:16

yes.
generally, it's about ... 12.2 USD (400 NTD)

彭士瑋
2015-12-28 22:51:57

http://www.amazon.com/s/ref=nb_sb_noss......

徐凡
2015-12-28 22:53:41

Maybe you can use this to replace 3M blue tape.
I bought it in Costco today,and I will try it tomorrow.

劉建良
2015-12-28 23:15:17

One question, what's the major application of your 3M blue tape # 2093EL ?

Dan Salvador
2015-12-28 23:15:51

adhetion for printing for extreemly large models

Joe Abaquin Bing Aquino
2015-12-28 23:57:00

Maybe this can help too...
I buy mine on any dollar store near my area. To better adhere .. I scratch the top with a fine sandpaper to stick very well. But I switch to hair spray. The bed & material can be Easily clean up by washing it off with a warm water.

原文網址 林學舜
2015-12-28 20:17:03

最近溫度偏低常會出現凸出狀況不知道各位先進會不會有同樣的裝況

Roy Lo
2015-12-28 20:24:46

PID 校正

原文網址 Chen Jack
2015-12-28 18:23:36

請問若要使用雙噴頭 ( ATOM 2.0 ) ---- 目前為單噴 ( 等雙噴中 )

要使用那一套軟體 --- 有真正支援雙噴頭的

3Q ~

張不凡
2015-12-28 18:36:09

kisslicer PRO 有...

Hawke ChienSheng Liu
2015-12-28 18:54:56

Cura, Simplify 3D

Chen Jack
2015-12-28 18:58:16

是的感謝目前看 Kisslicer 的官網 --- PRO 版本有支援多噴頭、 Cura --- 目前正在下載按裝中 ----- 期待 2.0 的雙噴開賣( 預訂 ) 多謝大家謝謝

原文網址 李木子
2015-12-28 17:01:14

傳統加工大多屬於減法加工
基本上很難透過「減法」完成這類型的作品
現在有3D列印及ATOM 2.0的幫忙
讓創意更容易實現

Robin Hsu
2015-12-28 17:50:26

好像是碳六十的結構 ~

李仁心
2015-12-28 19:49:44

這個用sla型的好像更好印的樣子

李木子
2015-12-28 22:09:12

有設計一顆更複雜的作品
近日會送印
完成後會跟大家分享～

原文網址 Dan Salvador
2015-12-28 14:36:32

design and modeling - what a great thing it is - and even better with Atom2.0

翻譯年糕

原文網址 蕭傑仁
2015-12-28 12:29:43

今天做了一個這個發現外圓跟設計的差不多（畫48 實際測試47.9）
但中心孔畫7mm 實際量測卻6.3mm 有大大知道這是怎麼了嗎？
我用的軟體是kisslicer

陳明谷
2015-12-28 12:33:15

圓圈容易會收縮

俞威名
2015-12-28 12:47:19

速度放慢來印看

Hawke ChienSheng Liu
2015-12-28 13:07:50

https://atom3dp.squarespace.com/printing-problems/
列印成品與原始3D模型有差異

Che Hung Wang
2015-12-28 14:19:53

收縮，無解。等數值模擬3D列印吧。

李穆
2015-12-28 14:24:17

先照劉大貼的校準方式校準到長寬各比50mm多一線寬，然後kiss設定inset surface半線寬

Clarence Lee
2015-12-28 15:00:33

不太算收縮..那是內圈擠比較多的問題..

Jie Yang Wang
2015-12-28 15:01:14

看紋路就發現是擠出量不準

李派克
2015-12-28 15:14:25

不大算收縮+1

陳奕丞
2015-12-28 22:53:59

kisslicer有個功能可以讓所有內圈往內縮一點
補償多擠出來的部分

原文網址 Joe Abaquin Bing Aquino
2015-12-28 12:09:22

Now that I have the free time. I finally assemble my new baby.

翻譯年糕

蕭傑仁
2015-12-28 12:30:58

Welcome to ATOM family

Joe Abaquin Bing Aquino
2015-12-28 12:42:00

Big thank U !

原文網址 Joe Abaquin Bing Aquino
2015-12-28 12:09:22

Birk Binnard
2015-12-28 12:24:03

Looks good - congratulations. I think most people put the PTFE tube inside the long plastic cable holder - that is not too difficult to do.

Where/how did you get the extra pinthead?

Joe Abaquin Bing Aquino
2015-12-28 12:43:13

I order at the same time with the Atom.

Joe Abaquin Bing Aquino
2015-12-28 12:48:11

And the tube, I like to see filament goes through.

原文網址徐凡
2015-12-28 08:37:23

原廠的線用習慣了
可是最近缺貨缺很大(白、透明)
不想等了，請問各位大大有沒有推薦的線材廠商

Odinson Thor
2015-12-28 08:40:21