ATOM 3D Printer Group 造訪社團

這麼神奇？～感覺是列印平台(熱脹冷縮？)或是end stop的問題～

要用auto home來調整嗎？

What version of firmware are you using? I have tried both 2.03 and 2.04 and neither of them remember Z-Offset. So I am going back to 2.02.

我的是之前沒有平台不平 現在有這問題 觀察後發現好像中間是凹的

Bug.

Yes - I thought it might be something like that.. An easy fix for sure. But for me 2.04 has the same problem as 2.03 - it does not remember the Z-offset values. So I will go back to 2.02 (again.)

Looks like clogged nozzle?Some toothpicks worked really good for me.

It was a clogged nozzle. Fixed it with the 0.400 mm drill and a small unfolded paperclip. US toothpicks are too thick. I wonder if there is an actual tool made for cleaning out 0.400 mm hot end nozzles. Seems like there should be.

And I wonder what causes the nozzle get clogged in the first place. Seems to me when it gets hot any PLA inside would get forced out by new filament entering the nozzle.

You did what I can't.

This is just example of great capability of Atom 2.0 for perfect adhesion

Did you recalibrate the
# define DELTA_DIAGONAL_ROD
& #define DELTA_RADIUS
in configuration.h ?
wondering if it changed with your effector installed position.

I didn't

Ive seen some of your prints and was fascinated about your quality. What slicer so you use? Do You change The settings for every Print? Want to get those results, too ?

it's so beautiful!!!!!!!

I use simplify3d , it seems to be the best when it comes to settings of even the smallest detail, it's also very harmonically communicating with Atom

Also consider using hairspray instead of glue stick

Ah okay good to know.The glue stick got on my nerves so I switched to Blue tape which makes such a great adhesion ❤ Buuut.. Do You change settings for every Print Part? I know some people who calibrate their slicers depending on their Print...Dunno how simplify works, but I'll get it for Christmas. Is it possible to export your Settings and upload them here? ?

I will put it on Dropbox and share here later ☺️ ☺️ ☺️

Thank you very much :) I am very excited about simplify3D

Hey Idan! Lovely raft. It does not look like hairspray, in your picture. Or is it simply a lot of hairspray?

Hey Idan Makutski , anything new on that simplify3D settings? :)

https://www.dropbox.com/....../2.2%20Lt%20PE......

here you go joschka friedl

Hey Idan Makutski , did you already delete it? Sadly I was only online on phone yesterday, so I couldn't download it.

Uh. It's gone.

sorry guys - here it is again (my staff deleted it )

https://www.dropbox.com/....../ATOM%202.0%20Single.fff......

Thanks Idan :) Will Test it on / after christmas ^^

哦哦哦讚啦ww

噴殺蟲劑試看看

好啦 正經回應
你有改裝快速接頭行程嗎
如果沒有的話回抽可以嘗試拉到10
回抹建議要嘛關掉要嘛5以上
回抽速度我是使用80
也有人使用到70

感謝~~我回去調整看看~:)

想要檔案wwww

http://i.imgur.com/XP6KRTl.jpg
我的支撐拆完很醜而且還在橋不好那個插槽T_T(插原版臉會掉下來)

請教陳大，有加裝快速接頭的墊片的話，會怎麼建議呢？

我開200度 8.8.5.80
是不會到拉絲

[Key Word] 快速接頭的墊片,這 ... 是什麼?

哈

哇，陳大 我沒改這麼大，只有加裝墊片而已說。效果有差嗎？

暖爐

噴頭溫度拉高

我現在噴頭195 那要拉到多少比較好？

200到205
Zoffset你是設定多少

改回玻璃口紅膠效果比較好，更好的是弄個便宜的低溫熱床

鋁擠熱漲冷縮，AutoLevel做一下就OK了，200度爽爽印~~

X-Wing

兩隻鱷魚

張大正解!!

高大幽默!!

http://www.thingiverse.com/thing:131466

期待星戰ing

今天已經原力覺醒

沒時間去電影院 哭哭

自已貼圖檔，原文沒圖檔。

好玩的是這個帳號啊... XD
http://sawareru.jp/en/

來挑戰看看

對，這個帳號的人超強的，他創作的作品好多啊，好像是專為視障的小朋友所做的。

http://www.atom3dp.com/zh/support-ch/

修正的好，而且連1代的也可以升級了