ATOM 3D Printer Group 造訪社團

原文網址 翁豪濬
2015-12-09 18:07:58

今天裝好雷射模組，按照說明書，先用噴頭進行自動校正，再換上雷射頭，開啟雷射光，但無論如何調整焦距，都無法在紙張上出現焦痕，請問是什麼原因呢?

林學舜
2015-12-09 18:17:53

用深色的紙試試

原文網址 Chun-chi Chung
2015-12-09 13:47:52

Clarence Lee
2015-12-09 14:41:07

trigger 100可能要考慮縮小到10 ?
因為這物件traveling的距離大部分都不會遠到100mm而觸發回抽...

Charlie Ting
2015-12-09 18:41:34

Prime 5, suck 5, wipe 0, speed 100, min jump 4, trigger 5.
Temp 190
Fan 0
開 wall 或 prime pillar 降溫。

原文網址 Chun-chi Chung
2015-12-09 13:47:51

牽絲很嚴重希望前輩們可以指導一下在哪裡可以再修改(ps:用明耀的PLA 點金)

Kwok Tony
2015-12-09 14:56:06

溫度到210會不會好些

林學舜
2015-12-09 17:55:05

風扇關小點看看

原文網址 Kwok Tony
2015-12-09 10:09:10

Eric Wu
2015-12-09 10:20:29

請問調到64% 幅度算大，有特別用意嗎!?

Kwok Tony
2015-12-09 10:25:38

因為沒有什麼支撐，第一次列印這麼久，信心不大怕有失誤，只是把速度調慢一點，增加成功率也增加細緻度。

原文網址 Kwok Tony
2015-12-09 10:09:09

11小時的成果，用CURA切片輸出Gcode SD Card打印，用Simplifly3D有問題。

Eric Wu
2015-12-09 10:22:00

請問用Simplifly3D 會出現什麼問題!!??因為我剛好也是這兩套交互用!!!所以請教一下

Kwok Tony
2015-12-09 10:38:19

站不住腳，加Raft也不行，可能是bug，CURA 就沒有問題

Eric Wu
2015-12-09 10:51:20

呵呵!剛好跟我相反，我印飛龍脖子跟尾巴分件時，用Cura 就是有幾顆不開brim ，調整也無效，改用Simplifly3D 才站得到地，能開brim!!!!呵呵…還真的不能只依賴一套啊!

Kwok Tony
2015-12-09 10:52:41

對，不能只依賴一套，起碼也要兩套

Stanley Ho
2015-12-09 11:24:58

Kisslicer 開brim

曾俊維
2015-12-09 14:14:33

我昨天用Simplifly3D，要印那個機器人，結果不知是不是回抽設定有問題，出料一直不順，用kiss就不會，我覺得kiss就差支撐了，支撐還是要在其他軟體先做好才行。

原文網址 Marge de Manoeuvre
2015-12-09 05:14:57

hello, can someone please tell me if :
when printer is on, the small fan behind the hotend start turning ?
the two side fans turns too? or they start if the hotend goes beyond 210° or stuff like that ?
because i never saw the two side fans turning, is it normal ? thanks a lot

翻譯年糕

Marge de Manoeuvre
2015-12-09 05:16:22

and the small fan keeps turning even if the printer is at 25° doing nothing, dont know if it should be like this, there is nothing about in troubleshooting section in the manual...

曾荐宏
2015-12-09 06:48:54

small fan behind the hotend is always turning when you turn on the atom2.0. Two side fans will turn when the machine start to work at the designation heights. (Offical setting is 3mm heights)

Marge de Manoeuvre
2015-12-09 06:54:53

ok, what to do if they never start after 3mm height ? i made successfull prints without them turning but i got some problems with curves when they are under the model with no support below : i think it's because the pla is not cooled enough, side fans not working... they are well plugged and the wires are ok, how could i check them or make a test to activate them ? what could i do please?

曾荐宏
2015-12-09 06:57:40

You can set heights in the slicer software.

Marge de Manoeuvre
2015-12-09 06:59:00

already done, is there a way atom team to perform a test to check the hardware and to see where the problem is ?

楊小隆
2015-12-09 07:06:37

Marge de Manoeuvre
2015-12-09 07:08:30

thanks a lot, i know this setting, but the fans just don't work, they are plugged, wires ok, connected to the atom board at the right place etc.... what could i do?

楊小隆
2015-12-09 07:36:24

Red circle upside down. change one then try again

Andrew Lee
2015-12-09 07:48:06

Andrew Lee
2015-12-09 07:48:56

quick way to turn on fan is in here: main menu > control > temperature > fan speed (any value above 0)

Andrew Lee
2015-12-09 07:52:42

check all the wire connectors again, make sure there is enough stripped wire to contact the actual terminals inside. if there isn't enough stripped wire, the contacts inside are only clamping onto the rubber and not the wire