• #maker+t=market
  • 3D列印服務
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Christopher Fugate
2020-03-18 00:06:01

I don't know if its because I finally tuned things in right, or if its just because I switched models, but I'm FINALLY up and running!

First mini print was technically successful, it stuck to the build plate and went all the way through. Lost an arm and a tail due to bad supports, apparently, but at least it worked!

Re-oriented and re-did supports, crossing fingers for a perfect print this time! I'm at least hearing a nice rhythmic thumping of the FEP, so at least I know its sticking!

翻譯年糕


原文網址 Christopher Fugate
2020-03-05 03:46:37

Jeebus Christie, at this rate I'm just going to superglue the damned FEP to the build plate. Thats the only thing anything sticks to!

翻譯年糕

Spiro Andritsis
2020-03-05 11:33:50

Michael Denney
2020-03-05 11:36:35


原文網址 Christopher Fugate
2020-02-28 06:24:20

Is there a setting somewhere to increase the build plate lift height during a print pause?

Because that tiny crack above the vat is not enough to get a proper view...

翻譯年糕

Diego Seminario De Col
2020-02-28 06:25:25

Tom Sargison
2020-02-28 12:34:41

Christopher Fugate
2020-02-29 03:40:25

Tom Sargison
2020-02-29 04:34:22


原文網址 Christopher Fugate
2020-02-27 21:18:42

I'd say my first print on the photon was a resounding success!

翻譯年糕

Janne Sjöström
2020-02-27 21:24:50

Kenneth Eben
2020-02-27 21:47:55

Gregory Strohmeyer
2020-02-27 21:56:22

Christopher Fugate
2020-02-27 22:28:22

Christopher Fugate
2020-02-27 22:44:07

Tom Sargison
2020-02-27 23:01:06

Christopher Fugate
2020-02-27 23:10:49

Christopher Fugate
2020-02-28 04:54:27


原文網址 Christopher Fugate
2020-02-27 01:25:52

Input Needed

So I've got my brand spanking new Photon set up and ready to go. I've done the default paper leveling method (home the bed without the vat, adjust down until printer paper pulls out with resistance but won't push back in, etc).

I've also seen the Flint Reed method.

Thing is, paper method does not mention moving the build plate back up a couple of 0.1's while the Reed method does. Or at least if the paper method does I missed it?

So do I need to re-level and give it a little space as the Z=0 ala Flint Reed, or is the "paper can slide out but not push back in" enough space for it as is?

翻譯年糕

Merv Hinton
2020-02-27 01:26:16

Christopher Fugate
2020-02-27 01:28:52

Chris Holden
2020-02-27 01:29:37

Keith Yinger
2020-02-27 01:30:41

Yaniv Lanzman
2020-02-27 01:32:05

Yaniv Lanzman
2020-02-27 01:32:27

Christopher Fugate
2020-02-27 01:34:11

Jenny Searcy
2020-02-27 01:37:18

Keith Yinger
2020-02-27 01:37:25

Christopher Fugate
2020-02-27 01:39:13

John Henry
2020-02-27 01:40:23

Christopher Fugate
2020-02-27 01:40:23

Yaniv Lanzman
2020-02-27 01:42:38

Jenny Searcy
2020-02-27 01:43:53

Jenny Searcy
2020-02-27 01:44:09

Christopher Fugate
2020-02-27 01:45:06

Yaniv Lanzman
2020-02-27 01:45:44

Janus Stark
2020-02-27 01:46:36

Yaniv Lanzman
2020-02-27 01:46:42

Yaniv Lanzman
2020-02-27 01:47:17

John Henry
2020-02-27 01:48:33

Janus Stark
2020-02-27 01:49:06

Yaniv Lanzman
2020-02-27 01:49:34

John Henry
2020-02-27 01:50:01

Yaniv Lanzman
2020-02-27 01:50:04

Yaniv Lanzman
2020-02-27 01:50:16

Yaniv Lanzman
2020-02-27 01:51:14

John Henry
2020-02-27 01:51:42

Yaniv Lanzman
2020-02-27 01:52:32

Christopher Fugate
2020-02-27 01:53:14

John Henry
2020-02-27 01:53:21

John Henry
2020-02-27 01:53:46

Yaniv Lanzman
2020-02-27 01:54:29

Christopher Fugate
2020-02-27 01:55:38

Yaniv Lanzman
2020-02-27 01:58:51

John Henry
2020-02-27 01:59:12

Yaniv Lanzman
2020-02-27 01:59:47

Yaniv Lanzman
2020-02-27 02:00:36

Yaniv Lanzman
2020-02-27 02:01:09

Janus Stark
2020-02-27 02:10:01

Yaniv Lanzman
2020-02-27 02:11:19

Yaniv Lanzman
2020-02-27 02:12:53

Janus Stark
2020-02-27 02:15:49

Yaniv Lanzman
2020-02-27 02:16:50

Keith Yinger
2020-02-27 02:22:57

Keith Yinger
2020-02-27 02:26:00

Jenny Searcy
2020-02-27 03:22:06

Chris Robinson
2020-02-27 10:34:22


 

討論主題

全不選 常用關鍵字