Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Julien Hmk
2020-03-25 23:41:16

I tried to print this file a few days back, relatively easy shape and I was in a rush so I just went with auto-support in chitubox, could have printed directly on the plate but I knew it would have been a pain to get off, when the print finished it came out all distorted, I thought that maybe my plate wasn't level anymore but the next print came out just fine, any idea where the problem could be ? My only theory so far is that I started printing at 20 degrees C and it finished at 35 C, printer is in an unheated room and the heater starts at the same time as the printer and forgot to switch it off, could that be it ?

翻譯年糕

罗西晟
2020-03-25 23:44:39

Supports not all up on the edges/corners.... That is most likely the issue here

Julien Hmk
2020-03-25 23:46:18

Xi-Sheng Luo forgot to mention I still used the file validator and there was no unsupported island

罗西晟
2020-03-25 23:47:08

Julien Hmk there might be no islands, but if the support does not reach the exact corner, that corner will "lift" due to the peel motion and stickyness to the FEP

Julien Hmk
2020-03-25 23:49:33

Ok I see what you mean, thanks!

原文網址 Julien Hmk
2020-03-19 04:22:51

An attempt at the tiniest articulated optimus prime..

25% of the original size

https://www.myminifactory.com/…/3d-print-articulated-g1-opt…

翻譯年糕

Julien Hmk
2020-03-19 07:41:27

After a couple of hours of assembly, not quite articulated anymore though, mostly CA glue holding it together but a good exercise ?

原文網址 Julien Hmk
2020-03-06 17:38:03

My macbook just died and I was running exposure test with anycubic eco resin, any way to tweak the exposure settings directly on the printer? I guess no but just asking

翻譯年糕

原文網址 Julien Hmk
2019-10-31 15:24:39

Anyone got good settings for anycubic blue plant resin before I run an exposure test ? Anyone got good settings for anycubic blue plant resin before I run an exposure test ? 翻譯年糕

原文網址 Julien Hmk
2019-10-02 19:36:43

Using chitubox and the photon file validator at the moment I'm just wondering, are you adding supports to every single pixel left after you fixed a file? Spend 4 hours doing supports on a figure and this thing is driving me nuts, still lots of minuscule islands are found.. I assume even the smallest cured pixel will have to be removed from the vat if unsupported? Haven't had to clean it or empty it yet..

翻譯年糕

Nathan Inwin
2019-10-02 19:57:13

Julien Hmk
2019-10-02 21:26:33

Ian Gill
2019-10-02 22:19:25

Julien Hmk
2019-10-02 23:15:21

Chamberlain Skeksil
2019-10-02 23:25:13

Ian Gill
2019-10-03 00:12:05

Julien Hmk
2019-10-03 03:32:28

Nathan Inwin
2019-10-03 10:22:46

Julien Hmk
2019-10-03 17:54:08

Nathan Inwin
2019-10-05 11:53:28

Julien Hmk
2019-10-05 13:59:08

Itai M Lustgarten
2019-10-09 22:17:58

原文網址 Julien Hmk
2019-09-21 06:32:50

I utilised some of the foam protecting the photon to make my UV chamber, compared to some "normal" LED strips the output of this one seems quite weak, used both a 5W and a 10W power supply and got the same result, photos below were taken with and without ceiling light on, opinion from other people who used similar ones?

翻譯年糕