• 3D列印服務
  • #maker+t=market
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Erik Wolvers
2019-11-28 01:04:28

Any one ever used this. For resin leaks?

翻譯年糕

Jarrod Smith
2019-11-28 01:23:12

Derek Reihe
2019-11-28 01:32:57

Jeremy Babcock
2019-11-28 02:19:11

Erik Wolvers
2019-11-28 02:20:16

Erik Wolvers
2019-11-28 02:23:03

Erik Wolvers
2019-11-28 02:23:39

Jeremy Babcock
2019-11-28 02:25:22

William Quayle
2019-11-28 03:36:59

Michael Garza
2019-11-28 04:07:09

Michael Garza
2019-11-28 04:07:55

Jarrod Smith
2019-11-28 05:39:11

El Ner Endem
2019-11-28 05:39:12

David Collinson
2019-11-28 05:40:09

JD Grimm
2019-11-28 11:37:09

Lou Steinritz
2019-11-28 11:43:11


原文網址 Erik Wolvers
2019-01-29 21:07:30

Now with more then 9000 members. There must be some Dutch members too. Were do you buy your resins?. And let me know your experiance

翻譯年糕

Erik Wolvers
2019-01-29 21:09:13

Boon Kheng Tang
2019-01-29 21:14:10

Saffron Ernst
2019-01-29 21:15:41

Erik Wolvers
2019-01-29 21:23:03

Tori Holmes-Kirk
2019-01-29 21:25:57

Erik Wolvers
2019-01-29 21:34:25

Boon Kheng Tang
2019-01-29 21:36:13

Sen Kun
2019-01-29 23:24:10

Sander Schonewille
2019-01-30 01:26:49

Boon Kheng Tang
2019-01-30 05:08:35


原文網址 Erik Wolvers
2019-01-27 23:03:50

Is there a resin that simulair to rubber.. need to make some tires Is there a resin that simulair to rubber.. need to make some tires 翻譯年糕

Stuart Presley
2019-01-27 23:05:58

Harley Hardin
2019-01-27 23:44:45

Frank Baeyens
2019-01-28 00:04:43

Harley Hardin
2019-01-28 00:06:45

Erik Wolvers
2019-01-28 04:04:55

Jack Sweek
2019-01-28 07:01:04

Fred Breton
2019-01-28 07:16:03

Johnson Yeh
2019-01-28 15:11:21

Charlie Anderson
2019-01-28 17:46:59

Erik Wolvers
2019-01-28 23:39:14

Erik Wolvers
2019-01-28 23:40:07


原文網址 Erik Wolvers
2018-06-06 17:53:33

Some tips
Mayby i am over causion. But i relevel the buildplatform after every print. Because i see after print it looses its level a bit. Prob. Due stickyness of print to the vat.
Shake resin everytime.
Autosupport in anycub slicer. Isnt great. Check support at corners.
If anything stuck to the fep. Dont remove it. Wil vat is on a hard surface. Put a piece of cloth under it. Otherwise youll damage the fep.
Removing the vat. Always tilt it first and then slide.
All prints must cure in uv. And remember Windowglass blocks a lot off uv feom the sun. So use Leds or go outside

翻譯年糕


原文網址 Erik Wolvers
2018-06-05 19:20:53

O wow. Clear resin is realy clear

翻譯年糕


 

討論主題

全不選 常用關鍵字