Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Casey Shiray
2020-02-11 23:50:32

Looking for an STL of this character (Tora) from Xenoblade Chronicles 2. Anyone know where I can buy or download one?

翻譯年糕

Daniel Künzle
2020-02-11 23:53:26

原文網址 Casey Shiray
2019-08-09 04:59:35

Anti-aliasing is only for the Photon-S?

Will it be coming to the original Photon?

翻譯年糕

Cam Erasmus
2019-08-09 05:02:08

Casey Shiray
2019-08-09 05:02:34

Stefan Giudici
2019-08-09 05:08:53

Melecio Guzman
2019-08-09 05:13:40

Tynbendad Dadtynben
2019-08-09 07:50:41

Rigo Arevalo
2019-08-09 15:54:29

原文網址 Casey Shiray
2019-03-05 00:07:33

Can anyone suggest a better way to clean prints. The toothbrush isn’t doing the trick for me.

I am still getting prints with leftover resin goo even after scrubbing them, especially in corners and small areas.

翻譯年糕

Kyle Curtis
2019-03-05 00:09:11

Christopher Thorpe
2019-03-05 00:13:51

Chris Crute
2019-03-05 00:27:27

Christopharius Cruzantium
2019-03-05 00:46:01

Evan Morgan
2019-03-05 01:51:34

Rob Elwell
2019-03-05 01:56:56

Dani Rose
2019-03-05 02:15:22

Ron Mitchell
2019-03-05 03:05:46

Robert Silvers
2019-03-05 11:55:18

Mark Peng
2019-03-05 12:08:13

Robert Silvers
2019-03-05 12:09:08

Susan Sioux Mercer
2019-03-05 16:01:17

Darren Tarbard
2019-03-06 14:21:26

原文網址 Casey Shiray
2019-03-04 08:18:35

Can anyone tell me why the base layer printed this way? Everything seems to have turned out fine.

翻譯年糕

Odie Fox
2019-03-04 08:26:08

Milton Maxson
2019-03-04 08:30:38

Mark Wardle
2019-03-04 08:36:58

Tim Vince
2019-03-04 18:37:31

Ed Del Rey
2019-03-05 11:00:48

Dustin Skye
2019-03-06 07:25:16

原文網址 Casey Shiray
2019-02-25 20:38:05

I may have leveled my printer incorrectly, or I’m reading the Github page wrong.

“Remember that as you tighten the setting (grub) screw it will move the plate down a tiny fraction more. You will find that you cannot pull the paper anymore, so you should raise / backoff the build plate level by 0.1mm increments until the plate is gripping the paper with even resistance, and that you can pull but not push it back. Then only set Z=0.”

So after doing the paper test AND tightening the setting screw, I should have backed off the plate until I could move the paper again—then set Z=0?

翻譯年糕

Bradley VanScoyk
2019-02-25 20:39:23

Christopher Elliott
2019-02-25 20:46:01

John Rudisill
2019-02-25 22:12:40

Sen Kun
2019-02-25 22:22:49

Casey Shiray
2019-02-25 23:31:14

原文網址 Casey Shiray
2019-02-22 09:25:43

If anyone would help me diagnosing what went wrong with this print, I would appreciate the learning experience!

In my typical fashion, I wanted to start my Photon experience with a bang and decided to skip the green cube.

I admittedly don't understand how supports work yet—at all. I get that if there is an overhang, supports give the overhang something to print on. But I'm having a hard time understanding how they help elsewhere.

Here is the model I tried to print:

翻譯年糕