Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Robin Haaf
2019-06-10 19:43:54

Before printing: don't forget to shake your resin! ? ?

翻譯年糕

Andrew John Monash
2019-06-10 21:08:30

Deividas Lidžius
2019-06-10 22:42:10

Daniel Amaral
2019-06-10 22:58:17

Chad Essley
2019-06-11 01:05:53

Nicolas Belin
2019-06-11 21:01:00

Nikolay Dimitrov
2019-06-12 00:55:24

Robin Haaf
2019-06-12 02:33:04

Chayanin Somton
2019-06-15 01:17:16

Aaron Denning
2019-06-15 07:09:38

原文網址 Robin Haaf
2019-04-28 06:39:11

What is a good and cheap alternative for a replacement FEP-film? I feel like a sheet of plastic shouldn't be more than 2€

翻譯年糕

Lucas Azd
2019-04-28 06:47:56

William Hardy
2019-04-28 06:55:10

Paul Youdelis
2019-04-28 07:31:03

Neil Ramsay
2019-04-28 07:44:01

El Ner Endem
2019-04-28 08:24:25

El Ner Endem
2019-04-28 08:29:23

Paul Youdelis
2019-04-28 09:49:06

Paul Youdelis
2019-04-28 09:50:01

Robin Haaf
2019-04-28 16:53:50

El Ner Endem
2019-04-28 17:14:33

Robin Haaf
2019-04-28 17:19:36

Neil Ramsay
2019-04-28 20:15:19

Neil Ramsay
2019-04-28 20:22:22

Peter Ede
2019-04-28 20:50:43

El Ner Endem
2019-04-28 21:13:36

Dan Smith
2019-04-28 22:12:40

Philipp Maitrot
2019-05-01 09:33:23

原文網址 Robin Haaf
2019-04-28 06:09:08

I changed the FEP film and after my first print I got these bubbles. Is there a protective layer I forgot to take off?
# GalaxyFoldwouldbeingoodhandswithme

翻譯年糕

Shayne Webb
2019-04-28 06:10:02

Paul Churchill
2019-04-28 06:18:52

Robin Haaf
2019-04-28 06:20:35

Trevor McIntosh
2019-04-28 06:21:31

Bard Vanhammer
2019-04-28 06:22:52

Paul Churchill
2019-04-28 06:23:02

Robin Haaf
2019-04-28 06:24:03

Paul Churchill
2019-04-28 06:28:30

Robin Haaf
2019-04-28 06:33:05

Benny Woolley
2019-04-28 06:36:18

Jerry Barnes
2019-04-28 06:40:06

Joe Lewis
2019-04-28 06:41:27

Mark Wardle
2019-04-28 07:01:51

Dave Smith
2019-04-28 07:03:00

William Hardy
2019-04-28 09:49:23

Jason Croft
2019-04-28 13:38:36

Peter Ede
2019-04-28 20:51:29

Leonardo Delgado
2019-04-29 10:54:44

Leonardo Delgado
2019-04-29 10:55:42

GaryAnji Smith-Lambeth
2019-04-29 23:03:03

原文網址 Robin Haaf
2019-03-12 15:11:12

Good morning all!
I have troubles with the quality of my print and have no clue why. Do you see the curvy first layer? It should have been flat. Why does this happen?
I'm thankful for any hint :)

翻譯年糕

James Cachia-Garrett
2019-03-12 15:25:42

James Cachia-Garrett
2019-03-12 15:26:07

James Cachia-Garrett
2019-03-12 15:26:50

Robin Haaf
2019-03-12 15:30:09

Robin Haaf
2019-03-12 15:30:23

Richard Thomas
2019-03-12 16:20:57

Sen Kun
2019-03-12 16:49:57

Robin Haaf
2019-03-12 16:51:40

Joel Ligeiro
2019-03-13 04:03:53

Robin Haaf
2019-03-13 04:07:57

Joel Ligeiro
2019-03-13 04:11:54

Robin Haaf
2019-03-13 04:12:50

Joel Ligeiro
2019-03-13 04:17:55

Robin Haaf
2019-03-13 04:19:03

原文網址 Robin Haaf
2019-02-28 23:47:27

I print with white opaque anycubic resin and after only 3 minutes of uv curing you can tell it becomes yellowish. Does anyone have similar experience while curing white resin?
Is there a resin out there that keeps its perfect white? And if not, what do you use for painting and not loosing any detail?

翻譯年糕

Philippe Maegerman
2019-03-01 20:49:50

原文網址 Robin Haaf
2019-02-28 19:00:29

Thank you for letting me be part of this community. I personally own an Photon SLA since a week now and its working perfectly. I'm very satisfied.

But there is one thing that is troubeling me: After the first print (photon initial cube) I got marks on the fep film. Since then I avoid placing prints in the center as I believe the film was bend to far by the suction of a centred piece. What do you guys think is the reason? It is still waterproof. But I should probably swap, right?

翻譯年糕