Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Olivier Clément
2019-12-20 23:44:20

Hey guys, just created a quick Remix on Thingiverse that may interest Peopoly/Siraya Resin users

It's a pouring spout that threads on those bottles;

It may not be perfect, I'm still getting used to Fusion and all that.

Hope this helps a few!

翻譯年糕

Olivier Clément
2019-12-21 07:25:33

原文網址 Olivier Clément
2019-07-10 03:48:51

Any resins (in white) that’d be better suited than others to spend time in humid/wet environment? (Eg: Shower)

翻譯年糕

Bob Deblier
2019-07-10 03:53:14

Jason Sutch
2019-07-10 04:03:21

Olivier Clément
2019-07-10 04:06:39

原文網址 Olivier Clément
2019-05-24 08:08:34

What could cause this kind of issues?
Been a few prints with this problem recently

Box with wall around 2mm thick
Printed in Blu and Sculpt mix in this case, around 60/40%. I also had the same problem with 100% Blu, however

Printed with Flat part directly on build plate
0.05mm
6 bottom lauers @ 60s
10s normal

翻譯年糕

Olivier Clément
2019-05-24 08:15:18

陳彦廷
2019-05-24 09:44:20

Olivier Clément
2019-05-24 09:45:19

陳彦廷
2019-05-24 09:48:23

Olivier Clément
2019-05-24 09:55:17

Slade Jokela
2019-05-24 10:18:44

Olivier Clément
2019-05-24 10:20:03

Andy Eakin
2019-05-24 10:26:06

Slade Jokela
2019-05-24 10:26:27

Slade Jokela
2019-05-24 10:32:49

Slade Jokela
2019-05-24 10:40:39

David McGyver
2019-05-24 10:42:27

David McGyver
2019-05-24 10:43:04

陳彦廷
2019-05-24 12:03:56

Olivier Clément
2019-05-24 19:49:29

原文網址 Olivier Clément
2019-05-07 10:47:50

ResinAway
How much would you say it can be reused?

I've been using it in an ultrasonic cleaner since day one (few weeks) and it was starting to cloud quite a bit. I put it under the UV in hope to cure/precipitate the dissolved resin and then filter it out, as Ive seen done with IPA.

Not sure it quite worked out: it turned yellow/brown-ish and didn't filter any particles really.
Could it still be reused in this state?

翻譯年糕

Trevor McIntosh
2019-05-07 11:00:39

Josh Norris
2019-05-07 11:18:38

原文網址 Olivier Clément
2019-05-05 13:23:12

New failure
Parts seem to have partially stuck to the plate
There was supposed to be 6 of them, 3 stayed on, 2 never stuck to the plate and 1 got to about 20% before falling from the plate

Based on the curve that symmetrical (supposed to be squares), it almost look like the plate isn't square...? Could it be something else?

Edit (also see photo in comments):

Photon S

Siraya Sculpt
0.05mm
6 bottom layers @ 60s
9s exposures

翻譯年糕

Bob Deblier
2019-05-05 19:09:32

Olivier Clément
2019-05-05 22:23:33

Olivier Clément
2019-05-05 22:25:17

Andrey Sabrev
2019-05-06 00:50:17

Olivier Clément
2019-05-06 00:51:57

Andrey Sabrev
2019-05-06 00:52:25

Andrey Sabrev
2019-05-06 01:00:54

Andrey Sabrev
2019-05-06 01:07:29

原文網址 Olivier Clément
2019-05-05 08:11:02

Just changed the FEP
Unfortunately overtightened within the frame so I had to keep it too tight working the vat (or it wouldn't rest on the LCD/screws would be an issue...)

Lowest I could go was around 396hz

Started a print with Sculpt, and the "pop" it makes she lifting is very loud, like 5 times more than with the old FEP. Am I looking for troubles by using it anyways or should I change again? ?

Edit: I'm an idiot
Had to walk away so I wasn't there to look at the print. The POP I was hearing was the whole vat lifting since I forgot to screw it in place ? ?‍♂️

翻譯年糕

Susan Sioux Mercer
2019-05-05 08:50:10

Chad Elstad
2019-05-05 08:59:04

Gregorey Savieo
2019-05-05 09:59:30

Olivier Clément
2019-05-05 10:09:32

Chad Elstad
2019-05-05 20:49:50

原文網址 Olivier Clément
2019-05-03 10:13:20

Success, fully articulated

Thanks to 陳小鎬 (hope I got the right profile :P ) for the settings!

翻譯年糕

陳小鎬
2019-05-03 10:16:19

Olivier Clément
2019-05-03 10:18:44

陳小鎬
2019-05-03 11:02:17

Dexter WG
2019-05-04 00:47:54

Olivier Clément
2019-05-04 00:48:37

陳小鎬
2019-05-04 01:03:52

Fernanda Carolina Aguiar
2019-05-04 14:37:12

Jack Hydrazines
2019-05-05 00:37:23

Jack Hydrazines
2019-05-05 00:37:47

Jack Hydrazines
2019-05-05 00:38:27

Jack Hydrazines
2019-05-05 01:40:11

原文網址 Olivier Clément
2019-04-29 09:15:40

Sooory for spamming these last few days... trying to learn the ropes here ?

Can't seem for the life of me manage to print a simple "box"
I tried a few different things (orientations, supports, etc)

Here's my latest attempt, that also failed (result in comments)
The supports stuck to the plate perfectly, but the model did tore away from the supports toward the end...

What should I try next?

This is in Siraya Blu on a Photon S

Thanks in advance

翻譯年糕