Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 David Scott
2020-04-02 10:19:58

I'm looking for STL files of the Scooby Doo gang. My intention is to print and paint and (eventually) use for my D&D game. Please share if you know where I can get the files.

翻譯年糕

原文網址 David Scott
2020-03-29 20:02:45

I'm looking for STL files of the Scooby Doo gang. My intention is to print and paint and (eventually) use for my D&D game. Please share if you know where I can get the files.

翻譯年糕

Pete Frith
2020-03-29 20:29:17

Following

原文網址 David Scott
2020-03-23 05:15:57

Dr Wolfgang Gesundheit in full plague gear

翻譯年糕

原文網址 David Scott
2020-02-10 04:05:51

I've been printing for about a year now and I'm starting get recurring failures like shown. Also, I leveled the bed just prior to this last print. Please help.

翻譯年糕

David Scott
2020-02-10 04:28:56

Luke Pettit
2020-02-10 04:37:31

Luke Pettit
2020-02-10 04:53:27

原文網址 David Scott
2020-02-07 01:34:14

I occasionally get failures like the shown image. Is that from loss of adhesion? Is it from bad supports?

翻譯年糕

Jared Davis
2020-02-07 01:38:27

David Scott
2020-02-07 01:41:01

David Scott
2020-02-07 01:41:04

Jared Davis
2020-02-07 01:43:20

Jared Davis
2020-02-07 01:44:03

David Scott
2020-02-07 01:55:17

Jared Davis
2020-02-07 02:02:08

原文網址 David Scott
2019-11-15 22:19:02

Time to buy resin. Found this article... https://www.windowscentral.com/best-resin-your-3d-printer Any thoughts? Do you agree? 翻譯年糕

Fahrid van Uitert
2019-11-15 22:20:31

Dan Hjulberg
2019-11-15 22:21:00

Clifford Schwankner
2019-11-15 22:44:04

Jeremy Swigart
2019-11-15 22:55:17

Robert Nisson
2019-11-15 22:59:57

David Scott
2019-11-15 23:55:14

Shawn O'Hara
2019-11-16 00:20:08

Mark Rhodes
2019-11-16 01:24:01

Brian Alexander
2019-11-16 01:55:31

Mark Rhodes
2019-11-16 01:58:09

Clifford Schwankner
2019-11-16 02:10:57

Clifford Schwankner
2019-11-16 02:11:36

Brian Alexander
2019-11-16 03:17:53

Mark Rhodes
2019-11-16 03:18:37

Sen Kun
2019-11-16 04:40:31

Shawn O'Hara
2019-11-16 08:44:31

Joe Broggio
2019-11-16 09:20:54

原文網址 David Scott
2019-10-26 05:16:07

Ok team, I'm going to print MZ's chicken on my Photon S. I'm using Anycubic Grey resin, .05 thickness, Norm Exp 18, Off 1, Bottom Exp 90, Bottom Layers 8. My intuition is to hollow the model and lean it back 45 degrees and manually add supports. I'd like to make a dozen of the chicks but I haven't had much success printing multiple models at once. How would you do it?

翻譯年糕

原文網址 David Scott
2019-09-23 09:41:45

The Dungeons & Dragons Phoenix, STL from Miguel Zavala that I printed on a Photon S then hand painted.

翻譯年糕

原文網址 David Scott
2019-09-23 03:04:49

https://i.imgur.com/2saEELX.jpg

The Dungeons & Dragons Phoenix, STL from Miguel Zavala that I printed on a Photon S then hand painted.

翻譯年糕

原文網址 David Scott
2019-08-11 03:19:42

Just spilled Anycubic Aqua Blue on my carpet! crap crap crap. Any way clean it up?

翻譯年糕

Rob Mayberry
2019-08-11 03:21:18