Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Jason Howe
2019-09-19 19:29:19

Will 355nm resin work on DLP printers, or does it need to be 405nm?

翻譯年糕

Bob Deblier
2019-09-19 19:32:34

Freddy Campione
2019-09-19 19:37:34

Bob Deblier
2019-09-19 19:40:22

Chad Elstad
2019-09-19 21:01:42

Ric Watts
2019-09-20 00:35:19

Herman Simpson
2019-09-20 02:53:18

Tiernan Messmer
2019-09-20 06:33:54

原文網址 Jason Howe
2019-08-30 08:32:08

Is it possible to buy a roll of FEP? I'm going to need some for a bigger print. Surely it's got to be cheaper if you buy it in bulk

翻譯年糕

Andrew Good
2019-08-30 08:37:44

Tori Beckett
2019-08-30 08:41:20

Tori Beckett
2019-08-30 08:41:58

Douglas Rector
2019-08-30 08:50:24

Jason Howe
2019-08-30 08:52:17

Chad Elstad
2019-08-30 09:44:24

Jason Howe
2019-08-30 10:31:08

Chad Elstad
2019-08-30 10:35:52

原文網址 Jason Howe
2019-06-06 17:25:01

I almost had a perfect print. Looks like the supports for the right foot and left elbow where not strong enough.
When I put the file back into chitubox to add some extra supports to them spots it said file was too big for full 3d model. Is there any way to fix this so I can modify this file or do I need to start adding all the supports to a clean stl?

翻譯年糕

Bob Deblier
2019-06-06 17:51:15

Jason Howe
2019-06-06 18:06:50

Andy Chung
2019-06-07 05:26:31

Jason Howe
2019-06-07 05:46:47

Andy Chung
2019-06-07 06:36:44

Jason Howe
2019-06-07 06:40:58

Andy Chung
2019-06-07 06:42:06

Kyle Urban
2019-06-07 16:11:51

Jason Howe
2019-06-07 16:20:31

Kyle Urban
2019-06-07 22:23:40

原文網址 Jason Howe
2019-06-03 09:58:11

Can someone please explain how the resin exposure finder works in a little more detail.
I understand that I need to pick the best column, probably 5 or 6 here then I need to double that to find the correct exposure time for this resin.
This was the 50 micron file, does that mean that the doubled exposure time of the best column is the right time for layer height 0.05? What if I wanted to prints at anything less then that? How do I work out the exposure time using the calibration test? I've read all the instructions that came with the fines but I'm still a little confused. Thanks

翻譯年糕

Tristram Chapman
2019-06-03 10:09:11

Jason Howe
2019-06-03 10:13:25

Tristram Chapman
2019-06-03 14:02:13

Jason Howe
2019-06-03 14:13:46

原文網址 Jason Howe
2019-05-29 11:10:22

I've just got some monocure rapid resin grey and I'm about to do the photon resin calibration for the first time. The test are only at .025 and .050. I'm looking to get the settings right for printing at .02 so how would I work that out? .025 is close but I thought it's better to not have layers moving along the 0.005. I've also had a quick look for YouTube videos to try and work it out but no luck.

翻譯年糕

Stefan Giudici
2019-05-29 11:25:44

Jason Howe
2019-05-29 11:26:56

原文網址 Jason Howe
2019-05-23 15:34:29

Had my printer for about 4 days now and getting amazing prints so far. When removing supports what do you use to clean the contact points up? Anything to sand them down or fill the small holes left behind in. The primed mini was printed at .04 with heavy supports on chitubox. The 4 unprimed ones where done at .02 with medium supports in chitubox

翻譯年糕