• 3D列印服務
  • #maker+t=market
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 John Cook
2019-07-17 04:04:05

New to Photon, pretty heavy layer lines on prints. Is it likely Z wobble or something else within my control that I can adjust within the software..Just using Photon slicer and default settings that were on it when I downloaded it.

翻譯年糕

Jarrod Smith
2019-07-17 04:06:07

Richard Humble
2019-07-17 04:06:58

Chayanin Somton
2019-07-17 04:07:44

Chayanin Somton
2019-07-17 04:08:10

John Cook
2019-07-17 04:10:31

Jarrod Smith
2019-07-17 04:11:24

Brandon Richard
2019-07-17 04:13:58

Chayanin Somton
2019-07-17 04:14:02

Chayanin Somton
2019-07-17 04:15:17

John Cook
2019-07-17 04:15:50

John Cook
2019-07-17 04:16:00

Jarrod Smith
2019-07-17 04:18:01

John Cook
2019-07-17 04:19:46

Gilles Miguel
2019-07-17 04:19:54

Jarrod Smith
2019-07-17 04:22:21

Andreas Zorpidis
2019-07-17 04:27:13

Armando Kerford
2019-07-17 04:30:14

John Cook
2019-07-17 04:30:14

Jarrod Smith
2019-07-17 04:31:46

Maurice Fitzgerald
2019-07-17 04:33:37

George Bulte
2019-07-17 04:34:43

George Bulte
2019-07-17 04:35:42

André Nettermann
2019-07-17 04:35:59

Gilles Miguel
2019-07-17 05:21:22

John Cook
2019-07-17 06:28:28


原文網址 John Cook
2019-06-30 06:58:02

So I bought this photon used on ebay, first time I tried to print It bound up in the bottom position and wouldnt move. When trying to re level it, it bound up again and upon further inspection, I noticed the part that slide up and down in the z rail is not installed correctly which I believe is the problem. My question is, how hard is it to get the cabinet off so I can re install the slider into the z rail properly.

翻譯年糕

Robert Mun
2019-06-30 07:04:18

Alex Munro
2019-06-30 07:07:03

Richard Shapiro
2019-06-30 07:12:28

John Cook
2019-06-30 12:41:30

John Cook
2019-07-01 05:13:08


原文網址 John Cook
2019-06-28 12:28:31

Bought a used photon. Supposedly 2 months old. Trying my first test print. The test cube on memory stick. Been running 45 minutes, screen still shows 1 percent. Cant tell if anythings happening. I can hear the fan and a bit of smell, but cant tell if anything else is happening. Keep waiting or abort?

翻譯年糕

Marc Fischer
2019-06-28 12:32:12

Jay Kay
2019-06-28 12:32:34

Eric Jorgensen
2019-06-28 12:43:15

John Cook
2019-06-28 12:51:39

John Cook
2019-06-28 12:57:06

John Cook
2019-06-28 13:01:36

Theo Nestora
2019-06-28 13:16:43

John Cook
2019-06-28 13:20:55

John Cook
2019-06-28 13:23:20

Trea Cotton
2019-06-28 14:24:29

Peter Chapman
2019-06-28 14:30:57

Trea Cotton
2019-06-28 15:11:01

Theo Nestora
2019-06-28 15:13:38

John Cook
2019-06-28 15:34:16

Peter Chapman
2019-06-28 15:35:11

Trea Cotton
2019-06-28 15:49:47

Peter Chapman
2019-06-28 15:56:29

Leonardo Delgado
2019-06-28 16:04:35

Trea Cotton
2019-06-28 17:51:57

Peter Chapman
2019-06-28 18:29:51

John Cook
2019-06-28 22:02:40

John Cook
2019-06-28 22:05:43

Leonardo Delgado
2019-06-29 00:56:02

John Cook
2019-06-29 02:17:46


 

討論主題

全不選 常用關鍵字