Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 David Bartholomew
2019-10-17 00:47:43

So I got this strange layer or two that a couple of large rectangles were cured we here there shouldn’t have been anything...and a bunch of supports just sort of stop at that point nearby...thankfully the missing supports didn’t cause a failure.

What would cause this?

Anycubic basic green
photon
8 bottom layers at 80s
Then 8s exposure time.
Time off 3

Got some other strange artifacts stuck to the bed frames there too....

翻譯年糕

Zena Andreou
2019-10-17 00:50:23

David Bartholomew
2019-10-17 00:53:14

Zena Andreou
2019-10-17 00:55:38

原文網址 David Bartholomew
2019-10-13 10:36:47

Anyone have any luck printing tiny (6mm - 10mm) infantry models?

Im looking for advice on layer height, settings, etc for the Photon with basic green or gray Anycubic resin. Does going down to say .01 layer height make a big difference?

翻譯年糕

Ric Watts
2019-10-13 10:43:41

Ludo Eksel
2019-10-13 10:58:42

Smith Hayward
2019-10-13 12:13:48

David Bartholomew
2019-10-13 12:30:59

Smith Hayward
2019-10-13 12:39:36

Michael Horn
2019-10-13 21:32:40

Smith Hayward
2019-10-14 05:47:36

Stefan Giudici
2019-10-14 06:24:32

Stefan Giudici
2019-10-14 10:02:10

原文網址 David Bartholomew
2019-10-13 01:14:32

This was my first print aside from the test one that came with the machine...I didn’t use auto-support....actually placed each one individually to make sure none of them bonded with the models...so as a beginner this had the potential to fail catastrophically....also, the print bed was out of level from the previous cleaning . AND, I forgot to tighten the screws that hold the bathtub down to the LCD screen, so the first layer pulled it up and dropped it! Despite all those factors, this print came out great. The fingers on the protrectrons are amazing.

翻譯年糕

Rolando Duarte
2019-10-13 01:19:44

Saleh Ballaith
2019-10-13 01:53:12

Jeff Greenfield
2019-10-13 01:56:16

Saleh Ballaith
2019-10-13 01:59:43

Jeff Greenfield
2019-10-13 02:06:40

Saleh Ballaith
2019-10-13 02:08:34

David Bartholomew
2019-10-13 02:34:53

Saleh Ballaith
2019-10-13 02:36:59

Alexx Butnotalex
2019-10-13 04:45:39

Alexx Butnotalex
2019-10-13 04:45:57

David Bartholomew
2019-10-13 05:07:58

Alexx Butnotalex
2019-10-13 05:15:18

原文網址 David Bartholomew
2019-10-11 10:59:25

Does anyone have a link to a file already set up to print (supports + angle, etc) on a new from factory set up using the sample Anycubic resin that comes with the printer? Something maybe 28-32mm gaming/terrain related? Maybe something small from Fallout? I’d like to be able to use my test print since this resin is so precious!

翻譯年糕

Stefan Giudici
2019-10-11 11:14:10

Greg Chapman
2019-10-11 11:25:11

原文網址 David Bartholomew
2019-10-11 10:38:22

Getting ready to do my very first test print...and noticed this defect where the resin vat frame meets the FEP in the corner there...really hoping resin doesn’t leak through there.

Any advice for a newb (that isn’t mentioned in the manual)?

翻譯年糕