Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Helen Schilz
2020-03-28 00:41:03

Good day all. I wounded if anyone has any suggestions. I have not been printing for the last few weeks as I had quite a few fails and got a little fed up. So I have now printed this file. The should have been 4 but 3 failed. I think my Z axis screw is slightly bent it's the second screw I have had. Any suggestions or advice would be welcome. Also had some weird print fail on the book case I printed aswell.

翻譯年糕

Mike Johnson
2020-03-28 00:42:46

What have you done? Are the failed prints stuck to the bottom or free floating?

Helen Schilz
2020-03-28 00:56:17

Stuck to the bottom... only the initial few layers seem to have printed. It's not the first time. I really do think its my printer. It had a faulty Z screw when I unboxed it and they sent me a new one which was ok for a few weeks then it started print failing again...

Sascha Berlin
2020-03-29 07:39:41

i had the some problem in the beginning. Make sure your resin is warm enough, sufficently mixed and have a higher exposure time on the first few layers. I went from 50 to 90. That solved ot for me. Also level the plate again. Maybe that helps

原文網址 Helen Schilz
2020-01-18 04:17:40

Just wondering what even spaced layer lines mean? Is my Z Axis off??
Posted before but no response ? Just wondering what even spaced layer lines mean? Is my Z Axis off??
Posted before but no response ? 翻譯年糕

Zak Williams
2020-01-18 04:20:06

Marc de Hoogh
2020-01-18 04:22:12

Helen Schilz
2020-01-18 04:49:56

Helen Schilz
2020-01-18 04:50:04

Brett Isaacs
2020-01-18 05:07:15

Helen Schilz
2020-01-18 15:34:38

Helen Schilz
2020-01-18 15:34:41

Helen Schilz
2020-01-18 15:34:45

Helen Schilz
2020-01-18 15:35:10

Marc de Hoogh
2020-01-18 15:36:00

Helen Schilz
2020-01-18 15:36:53

Marc de Hoogh
2020-01-18 15:44:23

Helen Schilz
2020-01-18 15:46:32

Marc de Hoogh
2020-01-18 15:50:21

原文網址 Helen Schilz
2020-01-17 21:44:16

Hello, I wondered if somebody could give me a little advise. I have been 3d printing for just over a year now. Got my Ender 3 in December 2018 (lots of mini and terrain). I wanted to print more detail on my minis so I also bought the Anycubic Photon in December 2019. My cube test print failed slightly, the Z axis screw was quite bent... not good. So I emailed customer support and they sent me a replacement. I changed the part and my next test cube came out fine. I have now printed about 30 minis but have noticed that they have layer lines and it seems to be getting worse. I have moved the Photon away from my Ender 3 just in case the vibrations where unsettling the resin and there has been no change. I have also noticed slight movement of the Z Axis screw (I think). I have re-leveled the bed a few times as one time the print bed had shifted so much that the front had risen by about 2mm. Hence the re-leveling of the bed. Sorry for the essay but I wanted to provide a fully view of my experience so far. Any help would be greatly appreciated.

翻譯年糕