Anycubic Photon Printer Owners 造訪社團

原文網址 Chris Legasse
2019-09-27 19:57:09

So I haven't used my photon for a few months. I've been really busy and haven't had a real need to until lately. I saw that there was a new firmware available so updated my firmware to the latest, re-leveled my build plate, downloaded the latest version of chitubox and just did a text print. I still have to figure out how to make this new threaded rod stop squealing at me (probably have to loosen some things) but after throwing a little paint on this I am basically in love with the details, like damn, I've not had a print come out this great before! No post processing on this piece at all other than paint. No sanding, no filing off the support pimples. Mostly because I printed this in transparent yellow so I couldn't even see any of the details or the pimples. Just an ultrasonic bath in IPA, and some paint :)

翻譯年糕

Roby Ellis
2019-09-27 20:02:42

Chris Legasse
2019-09-27 20:03:23

Chris Legasse
2019-09-27 20:03:59

Roby Ellis
2019-09-27 20:05:09

Tiernan Messmer
2019-09-27 21:46:13

Justice Fisher
2019-09-27 23:10:05

Chris Legasse
2019-09-28 06:08:44

Chris Legasse
2019-09-28 06:09:55

原文網址 Grégou Johnsonne
2019-09-27 19:31:13

Hey/
So i'm having my first failed print, support broke of rhe foot, and almost empty vat...

What should i do to clean tbe fep when the print is done?

翻譯年糕

Joe Estrada
2019-09-27 19:35:34

Grégou Johnsonne
2019-09-27 19:36:25

Lee Baxter
2019-09-27 19:37:45

Grégou Johnsonne
2019-09-27 19:38:37

原文網址 Haydar G. Al-Khateeb
2019-09-27 19:23:59

What is the best slicer that does automatic supports AND accepts prints without lift (direct on build plate) ?

I use chitubox but autosupports isn't good and its a big pain to add manual supports to thin islands

翻譯年糕

Chad Elstad
2019-09-27 19:28:55

Benjamin Hodges
2019-09-27 19:29:22

Haydar G. Al-Khateeb
2019-09-27 19:30:32

Haydar G. Al-Khateeb
2019-09-27 19:31:52

Chad Elstad
2019-09-27 19:33:24

Haydar G. Al-Khateeb
2019-09-27 19:35:06

Chad Elstad
2019-09-27 19:38:22

Haydar G. Al-Khateeb
2019-09-27 19:38:55

Benjamin Hodges
2019-09-27 19:40:46

Lee Baxter
2019-09-27 19:41:36

Dan Cowan
2019-09-27 19:44:50

Tomislav Štampar
2019-09-27 19:49:35

Ian Gill
2019-09-27 19:50:19

Derek Reihe
2019-09-27 19:56:57

Stefan Giudici
2019-09-27 20:37:39

Anthony
2019-09-27 20:44:02

Sherri Johnson
2019-09-27 22:30:36

Sherri Johnson
2019-09-27 22:34:04

Haydar G. Al-Khateeb
2019-09-27 22:53:27

Haydar G. Al-Khateeb
2019-09-27 22:54:06

Haydar G. Al-Khateeb
2019-09-27 22:55:20

Anthony
2019-09-27 22:56:39

Haydar G. Al-Khateeb
2019-09-27 22:56:59

Chad Elstad
2019-09-27 23:19:38

Haydar G. Al-Khateeb
2019-09-27 23:34:36

Stefan Giudici
2019-09-28 00:39:48

Ian Gill
2019-09-28 01:43:35

原文網址 Justin Wong
2019-09-27 19:17:19

Left my part in UV light too long for post curing. Printed in ANYCUBIC White, and now pinkish color.

翻譯年糕

Grant Weaver
2019-09-27 19:23:16

Gabe Snooks
2019-09-28 21:07:06

原文網址 Mitch Kalf
2019-09-27 18:59:36

Got my resin order today!

翻譯年糕

Antonino Giambino
2019-09-27 19:12:43

Mitch Kalf
2019-09-27 19:49:38

Adrian Carter
2019-09-27 23:26:29

Mitch Kalf
2019-09-27 23:29:15

Adrian Carter
2019-09-27 23:40:29

Michael Enoches
2019-09-28 04:58:02

Justin Lincoln
2019-09-28 05:17:00

Adrian Carter
2019-09-28 05:18:42

Alexander Alzate
2019-09-28 09:42:11

Mitch Kalf
2019-09-28 13:57:45

Juli Forthewin
2019-09-28 14:29:37

Mitch Kalf
2019-09-28 15:15:18

Matthias Hess
2019-09-28 20:01:21

原文網址 Nicholas DeRenzi
2019-09-27 17:51:57

Two questions. One, how does the anycubic green and grey do with heat? Would like to make a soldering jig, but not sure if the resin plastic will melt.....

Two, what's the build area on the photon?

翻譯年糕

Mark Wells
2019-09-27 18:01:37

Ben Johnston
2019-09-27 18:04:11

Ben Johnston
2019-09-27 18:04:38

Ben Johnston
2019-09-27 18:05:09

Nicholas DeRenzi
2019-09-27 18:16:25

Nicholas DeRenzi
2019-09-27 18:16:39

Jari Ivanoff
2019-09-28 06:37:19

Ryan Guenther
2019-09-28 14:02:19

Richard Webb
2019-09-29 00:12:42

Nicholas DeRenzi
2019-09-29 03:54:28

原文網址 Tiago Carita
2019-09-27 17:44:27

Hi guys, got my printer today, I have been working with FDMs for a long time and I'm a bit apprehensive that we cannot view the build plate and it takes time to check if we got any adherence. Any tricks for that?

翻譯年糕

Eli Tucker
2019-09-27 17:45:36