Anycubic Photon Printer Owners 造訪社團

原文網址 Steven J Greenfield
2019-09-08 05:16:59

Silly question, probably... I've not even gone through the first 250ml bottle that came with my Photon, but the 99% iso looks loaded with resin. Cloudy.

At what point do you give up on a tank of 99% iso?

How do you dispose of it?

Has anyone tried distilling it to get the iso back?

翻譯年糕

Jari Ivanoff
2019-09-08 05:23:12

Cam Erasmus
2019-09-08 05:23:35

Steven J Greenfield
2019-09-08 05:24:08

Ric Watts
2019-09-08 05:55:09

Chad Elstad
2019-09-08 09:04:48

Jari Ivanoff
2019-09-08 14:14:43

Ricky Cokely
2019-09-08 15:35:45

原文網址 Peter Foy
2019-09-08 05:15:11

Been getting partially cured resin and all sorts of feathery goop in the middle of models. LCD is doing this. Ribbon felt fine going into the board. Any thoughts on things to try?

翻譯年糕

原文網址 Jeremy Lauzon
2019-09-08 05:12:02

https://www.patreon.com/monstrousencounters/overview

原文網址 Stephen Wooten
2019-09-08 05:09:38

I've got an ultrasonic cleaner that I use to strip paint off old models. If I use it to clean uncured resin off of newly printed models, can I clean it so it won't contaminate any plastic models in there used later? Or is it then a "resin only "cleaner from then on?

翻譯年糕

Jari Ivanoff
2019-09-08 05:12:12

Jared Zadorozny
2019-09-08 05:14:06

Jon-paul Blinston
2019-09-08 05:16:39

Stephen Wooten
2019-09-08 05:17:07

Jared Zadorozny
2019-09-08 05:17:19

Steven J Greenfield
2019-09-08 05:18:00

Jon-paul Blinston
2019-09-08 05:21:36

Jon-paul Blinston
2019-09-08 05:23:34

Aaron Wiggins
2019-09-08 05:25:44

Jared Zadorozny
2019-09-08 05:26:00

Jared Zadorozny
2019-09-08 05:26:59

Jared Zadorozny
2019-09-08 05:27:59

Stephen Wooten
2019-09-08 05:34:37

Mike McCreery
2019-09-08 07:44:52

原文網址 Jamie Rasmussen
2019-09-08 05:09:21

After a slightly failed print last night (due to letting the resin sit waaay too long in the vat between prints), I cleaned it all up—including having to change the FEP due to slightly too vigorously scraping the accumulated buildup and punching a hole), filtered my resin and started it again.

The minis came out exactly as intended, but there was still a goopy mass of slightly hardened resin in the center of the FEP. Oddly, it doesn’t seem to have affected the print, but I think it may have accumulated while the sword of the guy on the right was printing (the other figures being complete at that point).

Any thoughts on what may have caused a buildup of half-cured resin in a spot not currently being exposed?

(Pay no mind to the dead looking owl familiar there; gotta switch in some clear resin to print him a stand. Also, apologies for not have photos of the build-up, but I was elbows deep in resin, trying to clean everything up to change out to the clear).

翻譯年糕

Jessica Pickering
2019-09-08 14:49:41

Jamie Rasmussen
2019-09-09 01:16:02

原文網址 Tim Hoogland
2019-09-08 04:59:00

So forgetting about my 1st gen photon not actually having UV blocking panels in it I lost a print and vat of resin. What's everyone doing to replace these non-uv panels?

翻譯年糕

Jon Weger
2019-09-08 05:16:41

Bentley Davis
2019-09-08 05:17:11

Tim Hoogland
2019-09-08 05:17:54

Nick Rubits
2019-09-08 05:43:54

Tim Hoogland
2019-09-08 05:44:20

Tim Hoogland
2019-09-08 05:57:16

Tim Hoogland
2019-09-08 07:38:35

Tim Hoogland
2019-09-08 07:38:45

Mark Wardle
2019-09-08 07:43:02

Tim Hoogland
2019-09-08 07:55:25

Jarrod Smith
2019-09-08 09:00:48

Tim Hoogland
2019-09-08 09:55:49

Bob Deblier
2019-09-08 17:21:45

原文網址 Dhaval Mistry
2019-09-08 04:58:44

Hey guys! I am new to resin printers and I have a couple of questions. I know the resin is toxic to bare skin but are the fumes exhausted from the back of the printer toxic also? Is there an air filter mod available for "Photon S" also? I tried searching the internet but couldn't find any and the backside of "S" is different than of photon. 翻譯年糕

Eric Calvin Rose
2019-09-08 05:00:50