Anycubic Photon Printer Owners 造訪社團

原文網址 Israel HV
2019-09-06 08:24:31

Best settings for anycubic translucent resin? Also, any castable resin suggestion? Im printing jewelery at first but the goal is to print mechanical pieces like gears and aluminum molds.

翻譯年糕

原文網址 Jacob Bolton
2019-09-06 07:51:43

Does anyone possibly know why this has occurred?

I’ve got to prints being built on the same bed both are exactly the same but the right leg and part of the trench coat of the model on the left hasn’t printed?

翻譯年糕

Ric Watts
2019-09-06 08:06:43

原文網址 Kyle J. Pendleton
2019-09-06 07:49:12

A question about miniature bases... do you all use the support to base option in your slicer? So the base of the mini is not on the printer's base... but is on supports?

My last batch of minis came out great... but there was some sort of issue with most of the bases being disconnected from the supports... so the bases of the minis are rounded a bit.

Or is this an issue with needing to level the printer again?

Sorry, I didn't take a picture to illustrate my mad rantings.

Thank you for any help provided ?

翻譯年糕

Kyle J. Pendleton
2019-09-07 02:49:42

原文網址 Steven Terrill
2019-09-06 07:14:00

Just subscribed to the Artisan Guild patreon. I noticed alot of models are in multiple pieces or at least with seperate bases. Is there an accepted best method for attaching models to bases? To you use resin and curing or some other method such as gluing or pinning?

翻譯年糕

Jesper Hvid
2019-09-06 07:17:35

Hugh Jeriolas
2019-09-06 07:18:29

Lucas Miguel
2019-09-06 07:19:15

George Bulte
2019-09-06 07:19:52

Steven Terrill
2019-09-06 07:26:58

Steven Terrill
2019-09-06 07:28:49

George Bulte
2019-09-06 07:30:16

George Bulte
2019-09-06 07:33:10

George Bulte
2019-09-06 07:34:22

Chad Elstad
2019-09-06 07:36:21

George Bulte
2019-09-06 07:37:02

Scott Pavlich
2019-09-06 07:44:01

Jesper Hvid
2019-09-06 13:36:46

Michael D Showalter
2019-09-06 20:55:16

原文網址 Brandon Taylor
2019-09-06 06:59:06

Anycubic Photon recieved, set up, and test print under way, 2% complete. Using elegoo grey and sliced with chitubox. Hope that doesn't mess anything up.

翻譯年糕

Brandon Taylor
2019-09-06 06:59:38

Brandon Taylor
2019-09-06 07:00:06

Nate Nelson
2019-09-06 07:03:09

Nate Nelson
2019-09-06 07:03:56

Brandon Taylor
2019-09-06 07:12:02

Brandon Taylor
2019-09-06 07:12:46

Hugh Jeriolas
2019-09-06 07:23:57

Tauri Icenogle
2019-09-06 11:56:51

Luke Carrington
2019-09-06 12:02:55

原文網址 Jonathan Stokes
2019-09-06 06:46:59

原文網址 Marvin Tomizzi
2019-09-06 06:34:27

Guys I don't know if it's just me but I find that print with anycubic gray resin gives more problems in term of warping and deformation than trasparent green resin, I raised the print parts to 18mm to avoid warped pieces. I wanna know your experiences with these two resins maybe I can find where I do wrong

翻譯年糕

John Rodriguez
2019-09-06 06:42:21

Lorenzo Castolo Melizza
2019-09-06 08:27:40

Marvin Tomizzi
2019-09-06 14:06:28

Marvin Tomizzi
2019-09-06 14:08:22

原文網址 Rory Kostman
2019-09-06 06:27:42

Tram to the panel, or tram to the FEP? My tram doesn't Look level, but print jobs are ok. I trammed to the build plate per instructions

翻譯年糕

原文網址 Kevin Rank
2019-09-06 06:26:13

If you are looking for some great miniatures to print on your Photon, there are a ton of active Kickstarters going on right now. There is also one that has a couple of statues you can print.

It was recommended I post this here. I hope some of you find this useful.

https://makerfun3d.com/3d-printable-terrain-miniature-kickstarters-september-2019 翻譯年糕

原文網址 John Tiyce-nelson
2019-09-06 06:19:35

Brains trust can you help guide me i have been getting odd blobs Of cured resin on prints and lines through the prints I’m using monocure rapid black with supports and the following settings:
Layer height 0.04
Bottom layers 8
Bottom layer exposure of 60
Layer exposure at 14s

翻譯年糕

Art Barrow
2019-09-06 06:37:31

Noah Lothes
2019-09-06 06:39:33

討論主題

發文排行榜

回文排行榜

熱門關鍵字