Anycubic Photon Printer Owners 造訪社團

原文網址 Philippe Radoux
2019-08-05 23:48:38

Hello everyone.

Thanks for adding. Hello everyone.

Thanks for adding. 翻譯年糕

原文網址 Conor Tanji
2019-08-05 23:48:14

Is there any good guide or rule of thumb for when choosing to use light, medium, or heavy supports?

翻譯年糕

Mark Wardle
2019-08-05 23:58:13

原文網址 Борис Смирнов
2019-08-05 23:36:11

原文網址 David Nicholls
2019-08-05 23:33:06

What are people using to fill drain holes?

I was just using resin+uv torch but it's sets as a separate part and when sanded/primed I can feel/see edges round the sealed hole.

I'm experimenting with Revell Plasto but it seems to want to stick to anything apart from model!!!

翻譯年糕

Mark Wardle
2019-08-05 23:45:13

David Nicholls
2019-08-05 23:48:27

Mark Wardle
2019-08-05 23:49:04

Michael Maxwell
2019-08-06 00:05:16

Michael Maxwell
2019-08-06 00:06:48

Philip Schifano
2019-08-06 01:13:25

Mark Wardle
2019-08-06 01:14:12

Maurice Criddle
2019-08-06 01:23:03

Ric Watts
2019-08-06 01:26:20

Richard Russell
2019-08-06 01:43:26

David Nicholls
2019-08-06 01:47:38

Richard Russell
2019-08-06 02:07:12

Richard Russell
2019-08-06 02:09:15

Chase Wichert
2019-08-06 02:54:19

Mike Fatchett
2019-08-06 02:55:16

Michael S Dooley
2019-08-06 07:56:37

Ben Cox
2019-08-07 05:39:57

Richard Russell
2019-08-07 05:46:18

原文網址 Theodore Garcia
2019-08-05 23:18:26

Wish me luck printing first print..

翻譯年糕

Kevin Lems
2019-08-05 23:26:52

原文網址 Joshua Collins
2019-08-05 23:10:31

First direct in the plate build with no supports. Incredible intricate detail!

翻譯年糕

Jeff Johnson
2019-08-05 23:13:12

Chris Shipman
2019-08-05 23:14:44

Gavin Starkey
2019-08-05 23:28:13

Joshua Collins
2019-08-05 23:38:26

Joshua Collins
2019-08-05 23:39:57

Gavin Starkey
2019-08-05 23:43:08

Joshua Collins
2019-08-05 23:44:36

Gavin Starkey
2019-08-05 23:44:45

Jeff Butler
2019-08-06 00:24:57

Gavin Starkey
2019-08-06 00:31:58

Chris Shipman
2019-08-06 02:46:59

原文網址 Przemek Antos
2019-08-05 23:01:33

How to run Resin Exposure Range Finder from Photonsters on Photon-S?

翻譯年糕

Vinicius Silva
2019-08-05 23:09:32

Michael Cargile
2019-08-05 23:26:36

Kevin Boogaard
2019-08-06 00:45:01

Chris Graf
2019-08-06 05:57:57

Kevin Boogaard
2019-08-06 05:58:49

Michael Cargile
2019-08-06 07:53:52

Michael Cargile
2019-08-06 07:54:52

原文網址 Michael Horn
2019-08-05 22:58:48

Hello everyone, new member here. I have two quick questions. First....if I change my layer height from .05 to .02, what changes woupd i need to make to exposure time? Second, it seems like every time i auto add supports, it bring the model up off the build plate and covers the bottom in supports. Is there a way to snap the model down to the build plate so it prints flat?

翻譯年糕

Simon Powell
2019-08-05 23:07:58

Bob Deblier
2019-08-05 23:23:16

Aaron Wiggins
2019-08-06 07:32:05

原文網址 Matt Hockenheimer
2019-08-05 22:44:41

Hold my beer, Photonkenstein's Monster is in progress...

翻譯年糕

Matt Hockenheimer
2019-08-06 03:42:51

Robert James
2019-08-06 14:23:16

Devin Wallace Simonsen
2019-08-07 00:15:58

Matt Hockenheimer
2019-08-07 00:25:52

Matt Hockenheimer
2019-08-07 00:27:06

Gary Houser
2019-08-08 03:01:05

Matt Hockenheimer
2019-08-08 04:15:25

原文網址 Brendan Mangano
2019-08-05 22:28:15

Hello all, new owner of 2 used Photon's. One crapped out after 3rd print, z axis won't respond, tried all the firmware/software fixes I could find. Im learning slowly how important supports are. In the photo below the supports seem to not want to connect to the model. Slicer ChiTuBox default auto medium supports and default slicer profile. Any insight on either of these issues would be much appreciated.

翻譯年糕

Justin Cupitt
2019-08-05 22:35:37

Robert James
2019-08-05 22:45:45

Andy Eakin
2019-08-05 23:30:51

Brendan Mangano
2019-08-06 02:27:44

Robert Maefs
2019-08-06 19:56:19

討論主題

發文排行榜

回文排行榜

熱門關鍵字