Anycubic Photon Printer Owners 造訪社團

原文網址 Jonathan Lopera
2019-08-03 21:34:38

Using meangreen i am getting these weird scuff results on my elegoo clear

翻譯年糕

Peter Boardman
2019-08-03 21:40:02

Peter Boardman
2019-08-03 21:40:24

原文網址 Gavin Starkey
2019-08-03 20:23:04

Tim Mulcahy
2019-08-03 20:30:31

Tim Mulcahy
2019-08-03 20:30:41

Gavin Starkey
2019-08-03 20:32:21

Tim Mulcahy
2019-08-03 20:33:19

Niall Forrester
2019-08-03 21:16:55

Gavin Starkey
2019-08-03 21:21:33

Niall Forrester
2019-08-03 21:21:56

Mika Vienonen
2019-08-04 04:11:20

Tony Healey
2019-08-04 17:08:27

原文網址 Michael Steadham
2019-08-03 20:15:21

Photon comes in tomorrow. My first resin printer. If anything like creality the resin that comes in the box won’t last one print. I bought this for d&d and 40k minis. What resin should I buy?

翻譯年糕

Stefan Derek
2019-08-03 20:18:20

Adrian Carter
2019-08-03 20:18:41

Tim Mulcahy
2019-08-03 20:18:46

Michael Steadham
2019-08-03 20:19:18

David Nicholls
2019-08-03 20:22:09

Scott Pavlich
2019-08-03 20:22:31

Greg Chapman
2019-08-03 20:23:06

Juju Mcgru
2019-08-03 20:29:08

Michael Steadham
2019-08-03 20:29:26

Greg Chapman
2019-08-03 20:35:38

Clint B. Kauffman
2019-08-03 20:42:53

Scott Pavlich
2019-08-03 21:05:47

Andrew Sutherland
2019-08-03 21:43:20

Michael Steadham
2019-08-03 22:06:02

Andrew Sutherland
2019-08-03 22:08:27

Robert Johnston
2019-08-03 22:31:48

Adam Jackson
2019-08-04 04:49:40

Michael Steadham
2019-08-04 06:22:22

原文網址 Georg Zoeller
2019-08-03 19:57:22

Sooo ... it looks like the official slicer is gone from the anycubic page?

翻譯年糕

Rick C. Patt
2019-08-03 20:03:52

Georg Zoeller
2019-08-03 20:04:46

Rick C. Patt
2019-08-03 20:06:47

Rick C. Patt
2019-08-03 20:07:12

Neil Ramsay
2019-08-03 20:09:35

Georg Zoeller
2019-08-03 20:16:27

Alessandro Rsx
2019-08-04 20:12:14

原文網址 Tom Stern
2019-08-03 19:47:15

OK so this is an improvement however why this kind of falts keep happening?

翻譯年糕

Tim Mulcahy
2019-08-03 20:17:08

Tim Mulcahy
2019-08-03 20:17:41

Tom Stern
2019-08-03 20:22:07

Tim Mulcahy
2019-08-03 20:23:36

Tim Mulcahy
2019-08-03 20:24:02

Tim Mulcahy
2019-08-03 20:24:29

Tim Mulcahy
2019-08-03 20:25:14

Tom Stern
2019-08-03 20:26:10

Tim Mulcahy
2019-08-03 20:27:10

Tom Stern
2019-08-03 20:36:08

Tim Mulcahy
2019-08-03 20:38:29

Bob Deblier
2019-08-03 20:38:32

Tom Stern
2019-08-03 20:56:22

Tom Stern
2019-08-03 21:50:48

Lorenzo Di Sante
2019-08-03 22:51:54

Tom Stern
2019-08-03 23:41:29

Tomas Salo
2019-08-03 23:53:31

Tom Stern
2019-08-03 23:54:19

Bob Deblier
2019-08-04 00:39:31

Tomas Salo
2019-08-04 01:27:07

原文網址 Lim Kim Yong
2019-08-03 19:37:19

原文網址 Scott Pritchard
2019-08-03 19:36:15

Wondered why I'd been getting a lot of print failures lately.

Turns out 1 of the screws on the frame the holds the FEP in place was much looser than the others, and the others had loosened off from what I'd secured them to originally, meaning the FEP had a lot more flex in it that needed.

If you're getting consistent print failures where they're stuck to the FEP, this should be the first thing to check as it's one of the easiest to do (more so than bed levelling).

翻譯年糕

Neil Ramsay
2019-08-03 20:12:29

Tim Mulcahy
2019-08-03 20:20:21

原文網址 Tobias Müller
2019-08-03 18:47:44

Hey guys, can u give me tips on how to place support or of the slicer settings to get sharp bases on angled miniatures? Hey guys, can u give me tips on how to place support or of the slicer settings to get sharp bases on angled miniatures? 翻譯年糕

Simon Deane
2019-08-03 18:54:29