Anycubic Photon Printer Owners 造訪社團

原文網址 Conor Tanji
2019-07-27 13:53:42

Mike Tongue The Banana Brigade won!! In a free for all between Deathguard, Eldar, Sisters of Battle, and Banana Brigade (Imperial Guard), the Bananas won by shear numbers to control the center objective point. Thank you so much for you models. My friends almost died when I unveiled the kill team. ?

翻譯年糕

Mike Tongue
2019-07-27 22:26:53

Mike Tongue
2019-07-28 01:19:31

Conor Tanji
2019-07-28 01:23:39

Mike Tongue
2019-07-29 00:53:09

Conor Tanji
2019-07-29 06:41:17

Conor Tanji
2019-07-29 06:41:22

Mike Tongue
2019-07-29 06:46:44

原文網址 Rigo Arevalo
2019-07-27 13:39:52

Ok, so I have dialed down (sorta mostly) and the support is sticking to the plate, but I have had a second print in a row separate from the supports, and only towards the middle of the build plate. I have checked it to see if it’s straight and it’s perfect. Any advice other than more support ?

翻譯年糕

Mike Fatchett
2019-07-27 13:52:54

Simon Stewart
2019-07-27 13:53:11

Rigo Arevalo
2019-07-27 14:17:48

Rigo Arevalo
2019-07-27 14:18:03

Simon Stewart
2019-07-27 14:32:31

Simon Stewart
2019-07-27 14:34:33

Rigo Arevalo
2019-07-27 14:44:37

Zena Andreou
2019-07-27 17:36:45

Chad Elstad
2019-07-27 23:43:26

Rigo Arevalo
2019-07-28 00:57:25

原文網址 Mike Fatchett
2019-07-27 13:34:02

Hot off the press! Black guard from Miguel Zavala . Elegoo Gray. .02 looks pretty good to me. Uncured. A bit blurry in spots. Print one in .05 just to compare. For our campaign .05 is fine.

翻譯年糕

Miguel Zavala
2019-07-27 18:19:25

原文網址 Vilius Jonaitis
2019-07-27 13:25:59

Anybody know where from this excess resin on my print

翻譯年糕

Susan Sioux Mercer
2019-07-27 13:29:20

Greg Chapman
2019-07-27 13:44:40

Vilius Jonaitis
2019-07-27 14:25:53

原文網址 Gregory RG
2019-07-27 13:05:43

I tried using the photon validator and it crashed my computer and somehow deleted my slicer program by using the validator is it always 100% accurate for prints?

翻譯年糕

Robert Maefs
2019-07-27 13:24:45

Robert Silvers
2019-07-27 14:04:27

Gregory RG
2019-07-27 20:53:58

原文網址 Sean Croteau
2019-07-27 12:56:35

Horray for the happy tapping thunk of success.

翻譯年糕

Sean Croteau
2019-07-27 12:58:15

原文網址 Kallon Fernandez-Tripp
2019-07-27 11:54:40

Is gorilla glue okay with anycubic resin?

翻譯年糕

Tim Moulton
2019-07-27 12:01:34

Kallon Fernandez-Tripp
2019-07-27 12:02:43

原文網址 Jason Turner
2019-07-27 11:07:20

Ok, so earlier I was asking about chitubox, and why my first attempt at this mini failed. I changed my settings to make sure I had more bottom layers and exposure time. I then leveled my build plate again and here's the result. I'm so very very happy!

翻譯年糕

Nick Williams
2019-07-27 12:17:54

Nick Williams
2019-07-27 12:18:02

Tauri Icenogle
2019-07-27 12:27:44

Bret Elliott
2019-07-27 14:08:11

Bret Elliott
2019-07-27 14:09:47

Jason Turner
2019-07-27 18:22:49

原文網址 Zachary Troendle
2019-07-27 11:05:24

Need some advice please:

Photon S - My second print came out pretty darned good, but it seemed to have a lot of little pock marks and lost a bit of detail towards the highest tip of the Z axis. Also there was quite a bit of that slime/jelly stuff in the resin vat afterwards. I heard the clacking of the model pulling away from the FEP film for the first 1/2 - 2/3 of the print, but nothing afterwards. The film also has indents on it from where the model began its support structures. Any tips to improve all this? Any of it just normal par for the course and expected wear and tear? It was printed at 0.05 with 10s exposure time and 8 bottom layers with 60s exposure. I used the auto support structure, but I think I'll start making my own because they came out a little more clumped and fully adhered to the print than the sliced file suggested.

Thanks all for the help, this is the best little printer.

翻譯年糕