Anycubic Photon Printer Owners 造訪社團

原文網址 Patrick Parkhill
2019-07-27 05:15:16

Curing questions. I bought a light see link.
Says it is Wavelength 395nm to 400nm. Is the 5nm difference going to be a problem? Don't really understand UV other than it gave me cancer one time. Also, curious how to know when a part is cooked? 30 sec, 5 minutes, an hour...How do you know? I do know that as I approached the lamp with gloves that had some resin on them they started to get hot and cure. So it's reacting. Just don't know if it's all proper like. Thanks in advance!

翻譯年糕

Stefan Giudici
2019-07-27 05:29:27

原文網址 Aaron Strome
2019-07-27 05:11:43

Hi everyone. just got my Photon and was so stocked until i put in the USB and it doesn't read it.. went to the page to get the slicer and it say 404 page not found.. has anyone figured out how to be able to use this printer.?

翻譯年糕

Aaron Strome
2019-07-27 05:13:48

Leonard Grubbs
2019-07-27 05:28:36

Ruth Suehle
2019-07-27 05:29:13

Aaron Strome
2019-07-27 05:30:04

Stephen Colin Richie
2019-07-27 05:49:37

Ines Silva
2019-07-27 06:12:01

Thomas Wright
2019-07-28 11:13:29

原文網址 Jim Allen
2019-07-27 05:11:38

I have been having problems printing this trike , on the photon I have had 3 failures now .
Model has been hollowed and holes added .
I tried a
25 deg ang
35 Deg
45deg

Now I have tried it flat so will see tomorrow

翻譯年糕

Joel Dawson
2019-07-27 05:48:49

Jim Allen
2019-07-27 05:50:17

Joel Dawson
2019-07-27 11:58:56

Jim Allen
2019-07-27 17:07:49

Joel Dawson
2019-07-27 17:35:56

原文網址 Rick Graham
2019-07-27 04:58:38

Hey guys,
What happens if there is uncured resin left in a hollow model that can’t drain? Does this lead to cracking in the model?

翻譯年糕

Stephen Colin Richie
2019-07-27 05:01:50

William Riker
2019-07-27 05:04:47

Rick Graham
2019-07-27 05:17:22

Stefan Giudici
2019-07-27 05:17:31

Stephen Colin Richie
2019-07-27 05:19:56

Stephen Colin Richie
2019-07-27 05:21:56

Mike Fatchett
2019-07-27 05:23:42

Michael S Dooley
2019-07-27 05:37:45

Gary Houser
2019-07-27 05:44:12

原文網址 Liam Woinson
2019-07-27 04:52:08

Hi guys I'm looking at ordering one of these printers. I currently have 5 FDM printers and looking to add a Sla to the mix. What are your opinions on them or top tips?

翻譯年糕

Will Shawcross
2019-07-27 04:53:26

Liam Woinson
2019-07-27 04:54:32

Will Shawcross
2019-07-27 04:55:38

Mike Fatchett
2019-07-27 05:05:57

Liam Woinson
2019-07-27 05:08:11

Mike Fatchett
2019-07-27 05:22:29

原文網址 Sargon Smith
2019-07-27 04:48:43

Has anyone done one of those print-in-place articulated models in an SLA printer?
I've done them with my FDM, but was wondering if it would even be possible in an SLA.

Like this, for example: https://www.thingiverse.com/thing:2064359 翻譯年糕

Kyle Calderwood
2019-07-27 13:34:41

原文網址 Aaron Marino-Drake
2019-07-27 04:45:05

Model, level, print, fail, clean, adjust, relevel, print, fail, clean, adjust, rerelevel, print, half fail, clean, rererelevel, print, success!

Next print, model, print, fail, back to top.

Am I doing it right? ?

翻譯年糕

Eric Jorgensen
2019-07-27 04:46:39

Aaron Marino-Drake
2019-07-27 05:48:45

原文網址 David Gottschalk
2019-07-27 04:38:35

Well, I was trying to get some slicing and printing done...

翻譯年糕

Mika Vienonen
2019-07-27 06:59:55

David Gottschalk
2019-07-27 07:27:38

原文網址 Doug Bowman
2019-07-27 04:22:09

So I was looking at the resin spreadsheet over on Photonsters and had a couple of questions as to how to make sure I bring those settings over to Chitubox correctly. Most of it was pretty straightforward, but in Chitubox there are two light off settings that I see (Light-off delay and Bottom Light off delay). I was wondering what the difference between those settings are and how the spreadsheet translates to the Chitubox settings?

Also, I'm assuming the settings on the right hand side are fine?
(screenshot of how I have it set up in Chitubox)

翻譯年糕

Anders Scot Hudson
2019-07-27 04:27:30

Matt Hockenheimer
2019-07-27 05:29:31

Doug Bowman
2019-07-27 05:33:34

原文網址 Bobby Bonner
2019-07-27 03:42:21

I need to print some bondtech bmg housings for my other printers. Was thinking of doing it on an FDM but thought the photon would offer better precision. What do people think of using it for this application?

翻譯年糕

討論主題

發文排行榜

回文排行榜

熱門關鍵字