Anycubic Photon Printer Owners 造訪社團

原文網址 Weston Miller
2019-07-01 18:57:23

Recently picked up my Photon and have had some success but more often than not, I end up with nothing but supports on the bed. I have changed the support settings to be heavy and added way more than needed. These prints are simple as well. So I have tried multiple orientations. I am also following the print settings for my resin that is posted on the Github page. The only thing that is tied to this recent change is when I plug my formatted flash drive in, I get the M_10000 (I believe) error where it asks you to unplug/plug the flash drive. I get it every time I go to print. Majority of this is operator error so I am looking for some advice on supports, print orientation, and maybe the error. Thank you, I appreciate your time.

翻譯年糕

Mark Wardle
2019-07-01 20:54:21

Weston Miller
2019-07-01 21:13:38

Scott Pavlich
2019-07-01 22:55:41

Weston Miller
2019-07-02 01:15:17

Greg Chapman
2019-07-02 06:49:09

Weston Miller
2019-07-02 07:08:10

Greg Chapman
2019-07-02 07:14:24

Scott Pavlich
2019-07-02 07:29:34

Weston Miller
2019-07-02 07:35:17

Weston Miller
2019-07-02 07:35:34

Scott Pavlich
2019-07-02 07:36:35

Weston Miller
2019-07-02 07:38:26

Weston Miller
2019-07-02 07:38:36

Weston Miller
2019-07-02 07:38:49

Weston Miller
2019-07-02 07:39:05

Weston Miller
2019-07-02 07:39:14

Weston Miller
2019-07-02 10:10:44

原文網址 James Campbell
2019-07-01 18:06:08

I have just installed ChiTuBox and i am wondering if anyone knows what the default settings are for the original photon (im using the anycubic green dental resin)? i'm concerned about the lift speed they were up at 300mm/min which seems fast? anyone know what a good speed is/ the default speed?

翻譯年糕

James Campbell
2019-07-01 18:10:29

Jason Sankovitch
2019-07-01 21:00:42

James Campbell
2019-07-01 21:06:28

Jason Sankovitch
2019-07-01 21:10:21

原文網址 Lestat De Lioncourt
2019-07-01 17:52:17

It's finally sticking to the bed, this is going to be my new gear knob, however I used chitubox to hollow out to 3mm but there seems to be weird shapes appearing inside the hollowed out model the chitu never showed on the hollow out preview

翻譯年糕

原文網址 Jakub Šrenk
2019-07-01 16:57:57

Which UV lamp you used? Please send me link on Ebay.
Thanks. :)

翻譯年糕

Ambrose Keen
2019-07-01 16:59:30

Richard James Sanchez
2019-07-01 17:45:35

David Cloete
2019-07-01 18:21:11

Ambrose Keen
2019-07-01 18:22:45

Ben Cox
2019-07-02 06:13:06

Eric Jorgensen
2019-07-04 04:04:55

原文網址 Saitama San
2019-07-01 16:33:55

Another impressive impression with Black Harzlab resin. 11s per layer. I still like the fluidity that makes it extremely easy to work. Model by The Maker Cult on patreon.
# harzlabs HARZ labs HARZ Labs Resins

翻譯年糕

Maik Nolte
2019-07-01 17:14:29

原文網址 Sydnee Davidson
2019-07-01 16:10:22

What’s the longest job you’ve run on a Photon? Is there a risk of overheating? I just started a 10hr print ? What’s the longest job you’ve run on a Photon? Is there a risk of overheating? I just started a 10hr print ? 翻譯年糕

Marcin Kudzia
2019-07-01 16:11:11

Charles Mercieca
2019-07-01 16:12:51

Kyle Urban
2019-07-01 16:12:56

Dániel Vœlkel
2019-07-01 16:14:03

Christopher Ashworth
2019-07-01 16:14:39

Dan Smith
2019-07-01 16:17:12

Richard James Sanchez
2019-07-01 16:20:23

Bob Deblier
2019-07-01 16:21:40

Fabio Ferrari
2019-07-01 16:36:23

Krunoslav Zlomislic
2019-07-01 16:47:02

John Smith
2019-07-01 16:47:57

Fahrid van Uitert
2019-07-01 16:53:34

Mark Kozik
2019-07-01 17:00:41

Danny Lloyd
2019-07-01 17:04:13

Jean-François Meloche
2019-07-01 19:18:54

Richard Shapiro
2019-07-01 20:15:19

Scott Pavlich
2019-07-01 20:39:59

Gary Houser
2019-07-01 20:45:23

Richard Thomas
2019-07-01 21:42:42

Robert Silvers
2019-07-01 21:46:42

Maggie Jenner-Bennett
2019-07-01 22:16:23

Maggie Jenner-Bennett
2019-07-02 03:29:36

Maggie Jenner-Bennett
2019-07-02 03:31:39

Maggie Jenner-Bennett
2019-07-02 03:32:51

Brandon Marcussen
2019-07-02 04:00:19

Steven Wood
2019-07-02 05:34:15

Sydnee Davidson
2019-07-02 05:41:49

Sydnee Davidson
2019-07-02 05:42:07

Sydnee Davidson
2019-07-02 05:42:12

David Martin
2019-07-02 06:56:15

Nizhen Phang
2019-07-02 19:15:42

Zäta Doe
2019-07-02 20:10:54

Chris Miller
2019-07-02 20:13:30

Steve Eldridge
2019-07-03 04:17:21

原文網址 谢信福
2019-07-01 15:39:32

原文網址 Russell Barnett
2019-07-01 15:12:56

Does a longer curing time on the first few layers result in better adhesion to the build platform? My last few attempts have fallen off and I wonder if that could be the issue as I have only used opaque colours before and am now using a solid grey.

翻譯年糕

Fred Bey
2019-07-01 15:15:52