Anycubic Photon Printer Owners 造訪社團

原文網址 Ricardo Moleda
2019-06-26 19:05:10

Hello Photonsters! Does anyone could guide my next steps with my issue? Thank you in advance!

翻譯年糕

Jarrod Smith
2019-06-26 23:21:38

César Fernández
2019-06-27 13:36:56

Ricardo Moleda
2019-06-27 18:22:03

Ricardo Moleda
2019-06-27 18:22:29

César Fernández
2019-06-28 16:26:59

原文網址 Vlado Turek
2019-06-26 18:57:39

原文網址 Jao Au Pinto
2019-06-26 18:48:43

I think i’m officially addicted to my Photon. Just 2 days into my holiday and thinking that you do not need a curing station if you live on Lanzarote and writing down new things to try once I am back. Luckely the wife didn’t allow the laptop in the suitcase, otherwise...

翻譯年糕

原文網址 Reggie Grahita Adhyatmaka Djatni
2019-06-26 18:45:08

First print with new color (anycubic) and it failed. Somehow my film also got messed up, but not punctured. I guess I need to buy a new one. Also closer look on the joint, but the picture not good...

翻譯年糕

Sercan Güzel
2019-06-26 18:47:29

Reggie Grahita Adhyatmaka Djatni
2019-06-26 18:48:40

Sercan Güzel
2019-06-26 18:50:14

Reggie Grahita Adhyatmaka Djatni
2019-06-26 18:54:47

Sercan Güzel
2019-06-26 18:56:22

Peter Ede
2019-06-26 18:58:42

Peter Ede
2019-06-26 18:59:08

Reggie Grahita Adhyatmaka Djatni
2019-06-26 19:00:40

Gustaf Sjögren
2019-06-26 22:37:22

Mark Wardle
2019-06-26 22:51:12

Mark Wardle
2019-06-26 22:51:58

Melecio Guzman
2019-06-26 22:56:32

Jean-François Meloche
2019-06-26 23:25:40

Mark Wardle
2019-06-26 23:26:37

Jean-François Meloche
2019-06-26 23:27:48

Mark Wardle
2019-06-26 23:28:33

Jean-François Meloche
2019-06-26 23:29:11

Gary Houser
2019-06-26 23:30:08

George Bulte
2019-06-27 01:08:28

Mark Wardle
2019-06-27 01:17:27

Stefan Giudici
2019-06-27 11:11:14

Reggie Grahita Adhyatmaka Djatni
2019-06-27 11:21:17

Reggie Grahita Adhyatmaka Djatni
2019-06-27 14:01:25

Stefan Giudici
2019-06-27 14:01:40

Reggie Grahita Adhyatmaka Djatni
2019-06-27 14:03:28

Stefan Giudici
2019-06-27 14:16:08

Reggie Grahita Adhyatmaka Djatni
2019-06-27 14:23:55

原文網址 Ben Gill
2019-06-26 18:20:55

Has anyone had problems with mixing monocure flex with resins? Mixed with anycubic maroon and got a failed print due to the opaque pigment seperating out

翻譯年糕

Stefan Giudici
2019-06-26 20:13:18

原文網址 Bruno Borges
2019-06-26 18:17:09

Hey guy´s, has anyone had this prob? When I print the stl printed is mirrored! To get it right I have to mirror the Z axis . I tryed to slice with Offcial Slicer and chitubox, in the software it looks good but when I print it´s mirrored. Try to upgrade firmware but the same. I kinda strange because I didn´t change any setting. Thanks in advance

翻譯年糕

Mike Tree
2019-06-26 18:25:19

Bruno Borges
2019-06-26 19:28:19

Sen Kun
2019-06-26 21:19:12

原文網址 Reggie Grahita Adhyatmaka Djatni
2019-06-26 17:08:46

Errr... Did I put too much resin?

翻譯年糕

Sercan Güzel
2019-06-26 17:11:16

George Bulte
2019-06-26 17:22:27

Fred Bey
2019-06-26 18:21:45

Jarrod Smith
2019-06-26 20:40:51

原文網址 Tom Kastrol
2019-06-26 16:01:33

Hi guys, after a week of getting to know my new Anycubic Photon and some failed attempts, I finally printed first bust.

Green and gray Anycubic resin.

Any difference between them? ?

I'll see after priming. ?

PS: I'm really glad I'm part of this group. Without the information I got here, I wouldn't print today.

Thanks to all

翻譯年糕

Luke Hayes
2019-06-26 16:22:32

Bob Deblier
2019-06-26 16:23:05

Tom Kastrol
2019-06-26 17:12:57

Chad Elstad
2019-06-26 20:47:45

Toby Kirkby
2019-06-27 07:51:42

原文網址 Theo Nestora
2019-06-26 15:01:04

Some help please!
I setup the photon and tried to do the sample cube that's on the usb drive with complete failure. Nothing stuck to the build plate at all but this (see photo) was stuck to fep.
The resin seems really thick. Is it supposed to be a really thick consistency?
I'm guessing my problem is levelling and I didn't go low enough maybe?
Any help would be great. Thanks.

翻譯年糕