Anycubic Photon Printer Owners 造訪社團

原文網址 Filipp Filipp
2019-06-09 00:07:56

I have a question how do you paint your models? With example please I have a question how do you paint your models? With example please 翻譯年糕

James Rooke
2019-06-09 00:21:47

Sean O'Hayer
2019-06-09 00:24:05

Amanda Kennedy
2019-06-09 00:44:44

Amanda Kennedy
2019-06-09 00:44:55

Kris Wirick
2019-06-09 01:06:56

Darren Donovan
2019-06-09 03:50:48

Reece Lewellen
2019-06-09 05:07:41

Jason Howe
2019-06-09 06:13:59

George Bulte
2019-06-09 06:59:45

Rhiannon Beorn Van D
2019-06-09 07:15:53

Henry Adams
2019-06-09 09:24:14

Lee Armstrong
2019-06-09 19:07:42

原文網址 Bob Martin
2019-06-09 00:01:11

That old nova3d resin is doing the job! with one coat of grey primer...

翻譯年糕

Raphaël Gerber
2019-06-09 03:38:36

Bob Martin
2019-06-09 04:14:43

Jesse Ferguson
2019-06-09 04:17:01

原文網址 Keenan Beblo
2019-06-08 23:41:30

How can I help models not come off supports during printing?

翻譯年糕

Ty Mansfield
2019-06-08 23:46:23

陳小鎬
2019-06-08 23:47:52

Bob Deblier
2019-06-08 23:48:26

Rob Mayberry
2019-06-08 23:50:07

Keenan Beblo
2019-06-09 00:08:26

John Goodrich
2019-06-09 01:34:47

Chad Elstad
2019-06-10 22:59:41

Ty Mansfield
2019-06-10 23:33:29

原文網址 Joe Alcantara
2019-06-08 23:33:46

Hi guys, a new day, a new problem.
Yesterday after my print I saw some resing on the LCD. I think the VAT tank bored. Does someone know what I can do to take off it? That is cured.

Thank you.

翻譯年糕

Susan Sioux Mercer
2019-06-08 23:37:26

Bob Deblier
2019-06-08 23:47:16

Adam Foster
2019-06-09 23:13:56

原文網址 Shawn Fisher
2019-06-08 23:28:08

I’m wanting to dial in my post processing some. I have not been soaking my prints in IPA, just rinsing and a light scrub with a soft toothbrush. Are you soaking and for how long? Also, I tend to IV cure about 20-30 minutes with a 10W UV light. This is the point where the part looks (in grey resin) a bit around the edges. How are you doing the post processing?

翻譯年糕

Bob Deblier
2019-06-08 23:45:50

原文網址 Nard Janssens
2019-06-08 23:25:09

Unboxing and first prints on the Photon by the Fugatech youtube channel:

翻譯年糕

原文網址 Scott Pavlich
2019-06-08 23:23:11

Another little project I’m working on for my nephew

翻譯年糕

原文網址 Alessandro Vasapolli
2019-06-08 22:45:18

Hello guys,

I’ve been experimenting a bit with pigments (specifically the Tianfour Sparkmaker pigments from aliexpress) and I have to say that added to anycubic transparent resin they print beautifully.
The problem is that, if left for long exposed to the sun, they basically fade away (blue becomes green and then almost yellowish).

Have you found some good pigments to color the resin leaving it transparent?
Anyone who tried with pigments for epoxy resin?

Thank you very much!

翻譯年糕

原文網址 Mike Tongue
2019-06-08 22:41:17