Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Adam Foster
2019-08-29 01:53:47

Does anyone have any settings for Printing on the Bed with PrusaSlicer please? I've tried setting 'Raise Height' to 0mm, but I get 'Elevation is too low for object' error. Can't any advice online. Thank you!

翻譯年糕

Mark Wardle
2019-08-29 03:22:27

原文網址 Adam Foster
2019-07-17 01:51:47

Hello chaps! Any idea if just adding a single hole to a small mini is enough? It's not really for saving resin, it's just to add a little flight base peg (2mm wide 4mm tall). Seemed easier then exporting the supported STL and using Meshmixer for example to add a hole. Hope that makes sense! Thanks.

翻譯年糕

Stefan Giudici
2019-07-17 02:11:41

Adam Foster
2019-07-17 02:13:41

Stefan Giudici
2019-07-17 02:15:37

Adam Foster
2019-07-17 02:18:50

Stefan Giudici
2019-07-17 02:22:09

Susan Sioux Mercer
2019-07-17 05:30:19

Chad Elstad
2019-07-17 20:47:30

原文網址 Adam Foster
2019-07-09 20:51:34

Hello all! I'm used to using Anycubic Skin colour. Does anyone have any exp with the Red or Orange colours please?

翻譯年糕

原文網址 Adam Foster
2019-06-24 23:20:03

Any advice on whether or not this'll work Printed flat on the bed? The lower 4 screw parts will adhere the piece to the Bed, but no idea about that under chassis section? Would it be supported by the 4 screw part 'legs'? Thanks! ? ?

翻譯年糕

Bob Deblier
2019-06-24 23:22:05

Seth Seth Dyte Dyte
2019-06-24 23:22:57

Bob Deblier
2019-06-24 23:25:54

Nicolas Tsagarides
2019-06-24 23:27:46

原文網址 Adam Foster
2019-06-06 21:01:17

Well, my time has come. The fep tore mid print, so now I have dried resin on the screen. I tried going at it with ipa and the plastic spatula but no joy. I've had a look on previous posts but haven't found much. Any tips please?

翻譯年糕

Ethan Brown
2019-06-06 21:03:52

Ethan Brown
2019-06-06 21:04:12

Ethan Brown
2019-06-06 21:05:08

Michael McElrath
2019-06-06 21:05:23

Randy Schaar
2019-06-06 21:06:18

Ethan Brown
2019-06-06 21:07:23

Randy Schaar
2019-06-06 21:07:46

David Nicholls
2019-06-06 21:23:32

Stefan Giudici
2019-06-06 21:24:02

Dennis Back
2019-06-06 21:44:02

Marshall Tearle
2019-06-06 21:50:10

Marshall Tearle
2019-06-06 21:50:21

Rick Denny
2019-06-06 23:52:24

Richard Thomas
2019-06-06 23:59:10

Randy Schaar
2019-06-08 09:40:27

原文網址 Adam Foster
2019-05-31 02:50:41

Hello all! Does anyone have any STL's for high poly Pokemon models? I've tried the usual suspects but nothing much is coming up. Thank you!

翻譯年糕

原文網址 Adam Foster
2019-05-14 21:33:43

Hello all! I've been using Anycubic Clear but it's currently out of stock so I've brought Anycubic Skin. I've checked that online spreadsheet, seems the two are similar settings-wise. Does anyone have any experience with Anycubic Skin or advice please? Thank you!

翻譯年糕

Sen Kun
2019-05-14 21:36:56

Richard Thomas
2019-05-16 21:19:20

原文網址 Adam Foster
2019-04-27 00:50:49

How often should I change my FEP please, chaps? I've been using the same sheet for about 6 months now, no probs, and I use the printer quite frequently. Does it only need replacing once it's damaged / ripped? Thank you!

翻譯年糕

Fabian Rodriguez
2019-04-27 00:56:06

Richard Shapiro
2019-04-27 01:37:47

原文網址 Adam Foster
2019-04-25 01:32:50

Evening all! Does anyone know how to manually add supports from the build plate in ChiTuBox? Constructed from the build plate, to the joint, to the support tip I've drawn in red. I'm trying to support this chap's 'underboob', but doing so adds one of those crappy mid-supports from the belly upwards. Hope that makes sense! I've had a look online but couldn't find any info. Thank you!

翻譯年糕

Arminas Didziokas
2019-04-25 01:52:21

Adam Foster
2019-04-25 01:54:07

原文網址 Adam Foster
2019-04-18 23:55:23

Does anyone have an idea on how to successfully print the top teeth on this mini on a Photon? ChiTuBox says there's no probs, but I can't see those top teeth printing without support. Any ideas? Thank you!

翻譯年糕