Anycubic Photon Printer Owners 造訪社團

Hello!

Im thinking on using some epoxy clay to seal this 2 holes, once dry I will prime it entirely.
Has anyone done something like this, will it be noticeable once primed?

翻譯年糕

So, I notice my prints seem to work without supports. I added rafts and got supports also using chitubox. Is there a trick to get only rafts without supports. I am supposing that need for supports is less in resin printing than fdm, probably because incremental building is so much smaller. Obviously, some prints require it. I was surprised, for example, the original cube print did not need supports. I'm getting partial failures that seem like would be solved with rafts. If i make my own rafts built into the model, what relative area is best, and what thickness? Thanks all.

翻譯年糕

hi all, any recommendations for the best settings to use with Elogoo LCD UV Rapid resin? hi all, any recommendations for the best settings to use with Elogoo LCD UV Rapid resin? 翻譯年糕

Hello Guys! :-)

So i know how the search-bar works and i used it ... but still i need specific help.

I got my Photon yesterday, did the testprint [worked perfect] then tried one of my prints and got the T_100 error. So searched for it - found solution -> Update! So i did. And i followed the instructions step by step and did the update correctly. Still T_100. Then i tried another version (4.1.2 or so) and got a T_110 Error. Now i downloaded another version from Github (a much older version to check) and got a different set of files and i dont know exactly what to do with them and what to "print".

See the pic below

翻譯年糕

I found some pretty sweet condition trackers for D&D that I remixed for printing on my Photon.
Unfortunately, the original design wasn't a good fit for resin.
Seems like there is a lot of tabletop players in this group, so I thought you might enjoy :)

翻譯年糕

For those with experience printing many small parts with Siraya BLU. I've been having good luck with larger items but running into an issue with smaller items.

These were supported using modified Large support settings in ChituBox(1mm contact diameter, .30mm depth, cone shape. Pretty big!)

I've printed the below about a dozen times in Anycubic Green at .02. No problems, all 30 helmets turn out gorgeous.

Printing the same with BLU, I'm noticing that the helmets around the outer row remain stuck to the FEP while the helmets inside of that outer box of helmets print just fine. I'm guessing this has to do with BLU being generally way more awesome at sticking to things combined with lesser peel force as you near the edges of the plate, but I'm not sure how to mitigate it.

Settings used with the BLU are heating to around 27c, .02 layer @ 10s 8 bottom layers @ 40s. I have decided to try the EPAX "Non FEP vat film" as some folks are telling me that it's pretty slick(no pun intended!) but it won't arrive for a week or so. I have resliced with the models clumped closer to the center of the plate, but I'm expecting similar results. Since really dialing in my Support settings in CtB, I haven't had issues of this sort with other resins.

That said, the pieces that are turning out in BLU are fantastic!

翻譯年糕

The Anycubic Photon is going on sale at 4:14 Mountain time (a bit over 4 hours from now). If you happen to be in the market for an FDM printer, the Mega S is also on sale on Amazon.

https://makerfun3d.com/amazon-lightning-sales 翻譯年糕

Ordered the parts for the chamber heater but I needed some heating immediately, so just used what I got handy.
Pretty ugly, but works. :)
How useful to have a laser cutter around...

翻譯年糕

Elegoo Black for $19.99 on Amazon again https://www.amazon.com/dp/B07R1VVVFG/ref=twister_B07R8BSH4R…

翻譯年糕

Okay, 1st batch only two thirds came out and something happened to the supports. 2nd different batch the ballerina's have half a leg missing? Took advice on settings. Help please ?

翻譯年糕