Anycubic Photon Printer Owners 造訪社團

原文網址 Josh Castle
2019-04-06 03:28:14

Hello all, new 3d printer owner here. I've tried 3 times to print, well anything with my Photon, and as of yet nothing has printed. Like nothing at all, not even a failed print. All I get is just the normal liquid resin pool in the base. Any idea what I might be doing wrong ?? Please help!

翻譯年糕

Marc Fischer
2019-04-06 03:30:48

Josh Castle
2019-04-06 03:41:40

Vinicius Silva
2019-04-06 03:43:16

Vinicius Silva
2019-04-06 03:43:47

Blaine Tsukayama
2019-04-06 03:44:02

Vinicius Silva
2019-04-06 03:44:08

Josh Castle
2019-04-06 03:46:18

Vinicius Silva
2019-04-06 03:46:59

Josh Castle
2019-04-06 03:52:04

Josh Castle
2019-04-06 04:53:03

Jason Bitter
2019-04-06 04:56:02

Blaine Tsukayama
2019-04-06 04:57:25

Blaine Tsukayama
2019-04-06 04:57:52

原文網址 Justin Lincoln
2019-04-06 03:17:01

I just got my Anycubic Photon up and running, I was using the Photon slicer and just read something about Chitubox? Does anyone have any more information or a small guide on how to set that up correctly?

翻譯年糕

Zena Andreou
2019-04-06 03:46:41

原文網址 Mikael Rasmussen
2019-04-06 03:16:58

Anyone have recommendations for some compatible High Temp resin?

翻譯年糕

Chad Elstad
2019-04-06 03:26:30

Jason Bitter
2019-04-06 03:39:13

Mikael Rasmussen
2019-04-06 03:58:49

Mikael Rasmussen
2019-04-06 03:59:05

Christopher Botha
2019-04-06 03:59:54

Christopher Botha
2019-04-06 04:04:23

Christopher Botha
2019-04-06 04:04:29

Christopher Botha
2019-04-06 04:04:35

Mikael Rasmussen
2019-04-06 04:05:30

Jason Bitter
2019-04-06 04:05:33

原文網址 David Nicholls
2019-04-06 03:08:37

Waiting on linear rails in post - no more Z-wobble...

Tried to fix using the Anycubic video - sure it would work great if one of the allen screws holding the eccentric nut wasn't stripped!

翻譯年糕

Vinicius Silva
2019-04-06 03:33:23

Robert Silvers
2019-04-06 03:59:06

David Nicholls
2019-04-06 04:00:30

Robert Silvers
2019-04-06 04:01:23

David Nicholls
2019-04-06 04:02:27

Luke Mason
2019-04-06 10:26:48

Toby Kirkby
2019-04-06 19:52:14

Fred Breton
2019-04-06 20:55:00

David Nicholls
2019-04-06 21:24:14

David Nicholls
2019-04-06 21:25:27

Vinicius Silva
2019-04-06 21:50:33

Vinicius Silva
2019-04-06 21:52:01

Vinicius Silva
2019-04-06 21:53:32

Vinicius Silva
2019-04-06 21:57:56

Keith Rea
2019-04-10 10:59:52

原文網址 Soraya Gouvea
2019-04-06 02:39:13

Hi guys! First of all I would like to thank you for the information shared in this forum! They have helped me a lot !! Well, I work with jewelry and am looking for a castable resin that contributes to a maximum richness of details within the possibilities of my printer which is a photon. I worked with b9 creator resins (Red and Cherry) on a generic (non-working) DLP printer, and it had great results! Both the printing of the models and the casting ... But in the photon I have not obtained good results, unfortunately ... The best I achieved was with a high exposure time of 80s, and even then still not enough ... impression lasted more than 25h !! I find it impractical ... So, can you help me by indicating burnable resins that you have already tested on the photon, which in addition to print quality are good for casting, and that work with shorter exposure times? ? Thank you!
Sorry for the bad english. I'm Brazilian.

翻譯年糕

Dustin Scott
2019-04-06 02:53:11

Soraya Gouvea
2019-04-06 03:00:44

Dustin Scott
2019-04-06 03:02:54

Soraya Gouvea
2019-04-06 03:04:11

Bhavik Gohel
2019-04-11 23:43:02

Soraya Gouvea
2019-04-12 02:32:16

Soraya Gouvea
2019-04-12 02:45:59

Soraya Gouvea
2019-04-12 03:06:12

Bhavik Gohel
2019-04-12 08:53:05

Soraya Gouvea
2019-04-12 09:05:06

原文網址 William Quayle
2019-04-06 02:30:52

Running into an issue with my prints- the first few layers of the model- NOT the supports- come out distorted, no matter what angle I've orientated.

Flat surfaces come out wavy if orientated parallel to the bed, and when I angled to 45 degrees surfaces get visibly distorted where it should be flat, etc. and it only occurs the first few levels of the model, so I’m confident that the issue is with something with the FEP film, but not sure if its a sign its installed too tight, or not tight enough.

Has anyone else run into this or have a solution?

翻譯年糕