Anycubic Photon Printer Owners 造訪社團

原文網址 Beau Lawrence
2019-03-17 18:44:16

So, when printing miniatures, should I use a oversized raft on the support less models so it's easier to remove them from the buildplate?

翻譯年糕

原文網址 Tiki ZBrush
2019-03-17 18:26:24

Hi, looking on the anycubic website I saw this there are also unboxing videos and more.

翻譯年糕

Sen Kun
2019-03-17 19:31:16

Tiki ZBrush
2019-03-18 00:39:00

Tiki ZBrush
2019-03-18 00:41:01

原文網址 Maxime Ecn
2019-03-17 17:57:34

In love with the photon. Prototype watch case printed with black anycubic resin ?

翻譯年糕

Che Fielding
2019-03-17 18:06:36

Chris Makris
2019-03-17 19:07:16

Maxime Ecn
2019-03-17 19:10:12

Andrew Beaton
2019-03-17 21:52:28

原文網址 Paul Fagan
2019-03-17 17:22:22

My photon arrived last night and I've just finished the test cube file that came with the stick. I have ordered a UV light to cure the prints but it won't arrive for a few days. Is placing the prints in a window going to provide enough sunlight to cure them in the mean time or should I just hold off on any proper prints until the new device shows up?

翻譯年糕

Mike Johnson
2019-03-17 17:24:39

原文網址 Mike Tongue
2019-03-17 16:54:25

After the (unexpected) love for the Banana Knight and subsequent squad of poses, I have completed a few more over the last few weeks for my Patreons https://www.patreon.com/bigmrtong

Also lots of free models and minis on my Thingiverse
https://www.thingiverse.com/BigMrTong/designs

翻譯年糕

Björn Ståhlnacke
2019-03-17 17:22:33

Patrick Vida
2019-03-17 19:37:14

Patrick Vida
2019-03-17 19:37:24

Mike Tongue
2019-03-17 19:48:54

Gabriele Giovanni Vecchio
2019-03-18 03:44:44

Fred Williams
2019-03-18 03:57:51

原文網址 Muhammad Zulkhairol Yacob
2019-03-17 15:55:03

Is there such correlation between area exposed vs cured time?

翻譯年糕

Robert Maefs
2019-03-17 19:52:29

Alexander Mihailov
2019-03-17 20:05:07

原文網址 Dani Rose
2019-03-17 15:30:21

Morning All - does anyone have any advice on the best way to print this type of object? I know these aren't so great at big flat sides etc and angles need to be considered but I'm a bit stumped. I printed the version with the 2 different angles on and they both had obvious lines on them - even though I angled at 45 degrees. I threw the file in t preform and it gave me roughly what's shown in the first and second image. Would this do the trick?

Many thanks

翻譯年糕

Mark Wardle
2019-03-17 15:41:58

Dani Rose
2019-03-17 16:04:20

Francesco Peeters
2019-03-17 16:16:22

Dani Rose
2019-03-17 16:21:13

Dani Rose
2019-03-17 16:45:26

Francesco Peeters
2019-03-17 18:02:26

Dani Rose
2019-03-17 18:45:40

Dani Rose
2019-03-18 03:04:05

Nick Santana
2019-03-18 06:53:07

Ken Lim
2019-03-18 07:15:03

Markus Schönfelder
2019-03-22 00:12:47

Sven Baedeker
2019-03-22 04:58:21

Sven Baedeker
2019-03-22 04:58:57

Markus Schönfelder
2019-03-22 07:53:55

原文網址 Nick Santana
2019-03-17 15:27:21

Does anyone know where I can get this model (or similar) reasonably?

翻譯年糕

Mark Wardle
2019-03-17 15:38:15

Mark Wardle
2019-03-17 15:51:10

Nick Santana
2019-03-17 16:34:44

Mark Wardle
2019-03-17 23:38:20

原文網址 Beau Lawrence
2019-03-17 14:14:58

When you print hollow objects to save resin, do you make drain holes in the top of the print (last pieces to print) or just whenever as long as it fits the design?

翻譯年糕

Mark Wardle
2019-03-17 14:16:33

Mark Wardle
2019-03-17 14:17:42

Stefan Giudici
2019-03-17 14:35:15

Beau Lawrence
2019-03-17 14:41:55

原文網址 Amjad Syed
2019-03-17 11:33:19

Thanks to everyone who helped me figure out my problem with failed prints... I'm guessing it may be related to temperature as I print in the basement man cave... anyway, upping the layer time to 60s seems to have worked, and I even lowered the supports to medium in ChituBox

翻譯年糕

Nick Williams
2019-03-17 13:16:05

Mario Toy Rossi
2019-03-17 16:13:58

Silvestro Zitelli
2019-03-17 18:07:00

Amjad Syed
2019-03-17 18:28:46

Amjad Syed
2019-03-17 19:17:52

Amjad Syed
2019-03-17 19:19:58

Silvestro Zitelli
2019-03-17 19:39:28

討論主題

發文排行榜

回文排行榜

熱門關鍵字