Anycubic Photon Printer Owners 造訪社團

原文網址 Bret Moye
2019-03-05 08:34:34

Does anyone have a link to get the slicer software? I upgraded PC and can't seem to find it again....

翻譯年糕

Greg Bauer
2019-03-05 08:56:24

Sen Kun
2019-03-05 13:21:32

Bret Moye
2019-03-05 13:22:37

Greg Bauer
2019-03-05 13:46:20

原文網址 Alex Cale
2019-03-05 06:12:37

My photon was just delivered today and it’s missing the resin vat ??‍♂️ . Has anyone dealt with anycubic’s support? If so how soon can I expect them to respond and send me one?

翻譯年糕

Sen Kun
2019-03-05 06:14:37

Alex Cale
2019-03-05 06:14:47

Kelly Wilkins
2019-03-05 06:15:27

Sen Kun
2019-03-05 06:15:59

Alex Cale
2019-03-05 06:17:10

Kelly Wilkins
2019-03-05 06:17:43

Alex Cale
2019-03-05 06:17:43

Daniel Hoke
2019-03-05 06:24:47

Alex Cale
2019-03-05 06:28:27

El Ner Endem
2019-03-05 06:29:09

Nick Santana
2019-03-05 06:35:47

Sterling Osment
2019-03-05 06:41:51

Michael M Thompson
2019-03-05 07:05:38

Alex Cale
2019-03-05 07:12:58

Garret Bertrand
2019-03-05 07:38:50

Robert Silvers
2019-03-05 08:14:15

原文網址 Danny Tix
2019-03-05 06:06:03

My photon was at the point where every single print would fail with a USB read error, even on new drives of a known-good model. I finally got around to disassembling the unit and noticed that my USB port was off-center and its shielding was touching the photon's outer case. Some quick electrical tape around the case opening and I'm back to printing*.

*During my first print after taping, half of the LCD went out; but this was resolved with a firmware update. Is there a connection? Who knows...

While I had the case open, I noticed that the USB port is pretty close to what I think is the power regulator for the UV light source. I didn't get a good look at the component, but there are some inductors on it right next to the USB port and I expect it's putting out some interference. I plan to do some proper testing and to maybe add shielding when I get the time, but I'm posting here now to gauge others' experiences and to see if anyone else sees an improvement from the tape. Does the EMF + grounding theory sound plausible to anyone else?

翻譯年糕

Darren Pawluk
2019-03-05 07:10:12

Chayanin Somton
2019-03-05 16:42:37

Darren Pawluk
2019-03-05 21:27:15

Danny Tix
2019-03-06 01:09:16

Darren Pawluk
2019-03-06 02:46:44

Danny Tix
2019-03-06 02:56:51

Darren Pawluk
2019-03-06 03:51:28

原文網址 Aaron Chambers
2019-03-05 05:51:10

Hey all-

What’s the largest print you have made on the photon ? (Does not have to be one single piece/print)

Post pics below

翻譯年糕

Kostas Filosofou
2019-03-05 05:55:36

Aaron Chambers
2019-03-05 05:58:03

Kostas Filosofou
2019-03-05 05:58:54

Orwin SantaCruz
2019-03-05 08:10:41

Orwin SantaCruz
2019-03-05 08:12:29

原文網址 Angel Antelo Martinez
2019-03-05 05:45:01

Soy casi nuevo en este foro, y espero que alguien pueda ayudarme, pues se estropeó el interruptor de corte y tengo que poner el que me ha mandado Anycubic. ¿Alguien me puede indicar cómo ponerlo.? Gracias Soy casi nuevo en este foro, y espero que alguien pueda ayudarme, pues se estropeó el interruptor de corte y tengo que poner el que me ha mandado Anycubic. ¿Alguien me puede indicar cómo ponerlo.? Gracias 翻譯年糕

原文網址 Andrew Jorgensen
2019-03-05 05:27:25

Anybody have any real-world feedback on the actual minimum x-y resolution of engraved features? I know the pixel size is around 0.047mm squared if I remember correctly more or less. However, I assume that light bleed prevents getting engraved features that will actually show at that width.

If not I may just have to run some test prints. Just hoping to get it done right with the first design iteration.

翻譯年糕

Kevin McGuigan
2019-03-05 05:40:10

Sen Kun
2019-03-05 05:45:41

Andrew Jorgensen
2019-03-05 05:53:51

Andrew Jorgensen
2019-03-05 05:54:15

Kevin McGuigan
2019-03-05 07:15:40

Robert Maefs
2019-03-05 08:25:14

Andrew Jorgensen
2019-03-05 10:21:20

Andrew Jorgensen
2019-03-05 10:22:21

Robert Maefs
2019-03-05 10:23:42

原文網址 David Chambers
2019-03-05 04:56:59

Pigeon print printed on anycubic photon in five parts.

翻譯年糕

陳彦廷
2019-03-05 07:31:52

David Chambers
2019-03-05 13:33:49

Dániel Vœlkel
2019-03-05 17:15:54

原文網址 Odie Fox
2019-03-05 04:41:24

Recent prints with the stock Anycubic Green. Alien, Yoga cat, cat statue, banana knight.

These were done at 0.05mm, 8s exp, 4 bottom layers at 60s each

翻譯年糕

原文網址 Chris Gough
2019-03-05 03:26:55

Just a general safety post, if you have pets please don't let them near your workspace. I had a gorgeous young cat who died a few days ago, he was only 2 and even though the vet said it looked like Antifreeze and that Methylated Spirits (what I've used to clean prints) wouldn't have done it I can't be 100% sure and feel terrible if he somehow died because of my hobby. I never saw him go anywhere near my jars but still, just to let you all know, be safe, it's fine if you willingly expose yourself to these things like I have but don't do anything that'd make you feel you might be responsible for the loss of a pet. I miss him so much and don't want people feeling as contorted as I am.

翻譯年糕

Kevin Kelley
2019-03-05 03:29:27