Anycubic Photon Printer Owners 造訪社團

原文網址 Jake Walker
2018-12-02 05:25:19

Hi folks. I have had a few days to play with my new printer and now I have come up with some questions.

1) What kind of cleaner/concentration of ethanol alcohol do you use to clean your build plate and vat?

2) I primarily use my printer to print miniatures for my D&D group. These are, on average, about 25-35mm tall and about half as wide. Sometimes when I try to build multiple of the same model at the same time some work and some fail. Sometimes I will get one or two that print fine, and then I will have others in the same batch that stick to the FEP film. For instance, I tried to print 6 of the same model just now. The 3 in the back row all printed fine, but the 3 in the front row all failed. What are some of the common causes of this? I have cleaned the FEP film and the build plate with 91% alcohol (all that was available at walmart) and I have re-zeroed the build plate as well.

3) Is there a rule of thumb as to how much space should be between models when you print multiples of the same thing? I would assume that since the image is coming directly from under the build plate the space between models isn't as critical, but I am also a noob and could be wrong.

4) How often do you have to replace the FEP film? I have already developed a wrinkle in the front right section of my film and am going to have to replace it. I attribute this to the number of failed prints that have been sticking to the film rather than the build plate, and in turn I have to go in and try to carefully scrape them off. What kind/brand of replacement film do you all recommend?

翻譯年糕

Jake Walker
2018-12-02 05:42:40

Christina Michelle Atteberry
2018-12-02 05:45:36

Dirk Ossebaar
2018-12-02 06:00:15

Dirk Ossebaar
2018-12-02 06:01:20

Kevin McGuigan
2018-12-02 08:48:52

Kevin McGuigan
2018-12-02 08:49:40

Jake Walker
2018-12-02 08:51:53

Jake Walker
2018-12-02 08:52:14

Dave Coggan
2018-12-02 10:19:50

原文網址 Sarvadaman Johari
2018-12-02 04:51:06

I'm trying to print hollow bangle in two parts but can't be able to print always stuck to tray can anybody help me please? I'm trying to print hollow bangle in two parts but can't be able to print always stuck to tray can anybody help me please? 翻譯年糕

Mark Wardle
2018-12-02 04:54:34

Mark Wardle
2018-12-02 04:56:45

Mark Wardle
2018-12-02 04:58:06

Mark Wardle
2018-12-02 05:24:38

Mark Wardle
2018-12-02 05:25:55

Sarvadaman Johari
2018-12-02 05:28:43

Mark Wardle
2018-12-02 05:40:12

原文網址 Joel Gillespie
2018-12-02 04:34:46

I just got my printer, haven't printed yet. After an .stl file has been sliced and saved as a .photon file in the anycubic slicer, is it normal not to be able to reopen it in the slicer and edit it?

翻譯年糕

Tim Allen
2018-12-02 04:38:25

Joel Gillespie
2018-12-02 04:44:33

原文網址 Nikola Petrov
2018-12-02 04:18:51

Welcome to the family Photon! :D

翻譯年糕

Sen Kun
2018-12-02 12:24:31

Sen Kun
2018-12-02 12:25:01

原文網址 Julia Adams
2018-12-02 04:17:14

Hi Folks.
Anycubic Grey.
Layer: 0.035
Exposure time: 10
Off time: 1
Bottom Exposure: 90
Bottom Layers: 8
There seems to be shiny patches all over the models, it looks like un-cured resin (but it isn't)
Any ideas? I'm guessing either too short an exposure time or I didn't shake the bottle enough before starting.
Thank you :)

翻譯年糕

James Cachia-Garrett
2018-12-02 04:38:00

Richard Shapiro
2018-12-02 04:39:18

Julia Adams
2018-12-02 05:10:19

Julia Adams
2018-12-02 05:10:55

James Cachia-Garrett
2018-12-02 05:24:27

Mark Wardle
2018-12-02 05:42:01

Dave Corbett
2018-12-02 09:10:50

Sam Cunningham
2018-12-03 06:00:42

原文網址 Ohad Daya
2018-12-02 04:05:39

Hi
Is anyone using Formware 3D ?
I don’t understand how the support work there
Glad for a little help
Thanks

翻譯年糕

Jon Piercy
2018-12-02 05:55:37

原文網址 Nick Santana
2018-12-02 03:22:12

This is why I don't post cure clear resin.

翻譯年糕

Zena Andreou
2018-12-02 03:27:43

Tiago Marques
2018-12-02 03:32:01

Zena Andreou
2018-12-02 03:33:34

Fred Breton
2018-12-02 03:42:15

Zena Andreou
2018-12-02 03:43:32

Tiago Marques
2018-12-02 03:44:29

Paul Mendoza
2018-12-02 04:33:35

Fred Breton
2018-12-02 05:02:36

Nick Santana
2018-12-02 06:20:32

Fred Breton
2018-12-02 06:35:19

Nick Santana
2018-12-02 06:44:05

Jaco Norchie Nortje
2018-12-02 10:52:43

Nick Santana
2018-12-02 10:54:47

Stefano Corinaldesi
2018-12-02 15:22:41

Sen Kun
2018-12-02 17:45:59

Guido A. Mandorf
2018-12-02 21:41:13

Guido A. Mandorf
2018-12-02 21:42:46

Nick Santana
2018-12-02 22:50:04

Guido A. Mandorf
2018-12-03 00:03:31

原文網址 Eric Jensen
2018-12-02 03:22:09

Pretty much click and print at this point. Primed Anycubic Green with ChituBox slicer @.030 layers. Two radiators and an intake duct, both for a ship model.

Zero experience a week ago, this is a piece of cake now.

翻譯年糕

Sen Kun
2018-12-02 12:30:00

Horris Borris
2018-12-02 12:40:09

Brian Morin
2018-12-02 12:40:59

Eric Jensen
2018-12-02 14:24:41

Eric Jensen
2018-12-02 14:27:02

Brian Morin
2018-12-02 21:35:14

Orwin SantaCruz
2018-12-03 10:12:34

Eric Jensen
2018-12-03 10:15:47

原文網址 Dennis Bouffard
2018-12-02 03:20:55

Hay guys....I got the same model as see in the page banner, so I was wandering....I read a lot of people using Ultraviolet light to finish curing you prints....what are you guys using...and will plant lights work for do I have to get a uv light?

翻譯年糕

Роман Хариков
2018-12-02 03:26:43

Zena Andreou
2018-12-02 03:27:03

Richard Shapiro
2018-12-02 03:57:38

Dennis Bouffard
2018-12-02 04:16:57

Dennis Bouffard
2018-12-02 04:18:07

Dennis Bouffard
2018-12-02 04:18:47

Richard Shapiro
2018-12-02 04:20:52

Dennis Bouffard
2018-12-02 04:23:51

Richard Shapiro
2018-12-02 04:26:36

Dennis Bouffard
2018-12-02 04:29:52

Richard Shapiro
2018-12-02 04:31:40

Richard Shapiro
2018-12-02 04:31:52

Dennis Bouffard
2018-12-02 04:32:34

Dennis Bouffard
2018-12-02 04:34:31

Richard Shapiro
2018-12-02 04:35:20

Richard Shapiro
2018-12-02 04:35:36

Jon Piercy
2018-12-02 05:47:24

Jeremy Lauzon
2018-12-02 05:52:30

Jon Piercy
2018-12-02 06:04:54

Che Fielding
2018-12-02 13:00:09

Jon Piercy
2018-12-02 22:34:35

Jon Piercy
2018-12-03 19:24:51

Che Fielding
2018-12-03 22:45:31

Jon Piercy
2018-12-04 00:28:11

Che Fielding
2018-12-04 00:46:50

Jon Piercy
2018-12-04 03:15:46

Che Fielding
2018-12-04 04:47:13

Jon Piercy
2018-12-04 05:13:09

Che Fielding
2018-12-04 05:27:23

Jon Piercy
2018-12-04 05:28:17

Che Fielding
2018-12-04 05:55:04

Dennis Bouffard
2018-12-04 06:54:49

原文網址 Richard Shapiro
2018-12-02 02:58:32

I had an interesting experience with my last bottle of Anycubic Gray resin. Despite shaking it until my arm got tired before each print, it was nowhere near properly mixed.

The first prints I got out of the top of the bottle were beautiful, but very brittle, and they stuck to the plate like fury.

By the end of the bottle, I was getting prints that were more flexible, much stronger, and not sticking well to the build plate, even though I was printing from similar files using similar techniques.

So, other than the FEP aging over the course of the bottle, which certainly may have affected how sticky it is, the only real variable here is what portion of the resin mix I was getting in the vat.

So, here's my solution. Call it a miniature paint mixer. It's the propeller shaft and prop from a model boat. The shaft is 4mm and the prop is 25mm in diameter. It fits through the mouth of every resin bottle I've got, except for the Monocure 500ml. I can always get a smaller prop, though.

This seemed to do a good job of agitating the resin, and at about 2000 rpm (pushing the resin down, not pulling it towards the cap), it wasn't spraying resin everywhere - only a drop or so off the shaft.

I've got a print going now that failed yesterday with the Anycubic Gray. I'm out of that resin, so this is Monocure Black with about 20% Flex added. The only thing I've changed is the resin and the mixing. If this one fails, I'll change the FEP. If that one fails, I'll try Rain-X on the FEP. If that fails, I'll try Platebond.

If that fails, I'll sacrifice a goat to ... aaaah just kidding.

EDITED: First Monocure print 95% successful. I had one support "disappear" and one corner of one piece has a bit missing. But - it's a servo mount and the missing bit isn't an issue.

翻譯年糕