Anycubic Photon Printer Owners 造訪社團

原文網址 Joey Pruitt
2018-11-25 01:48:49

Latest sculpts and prints.... 35mm

翻譯年糕

Simon Powell
2018-11-25 09:42:25

原文網址 Lưu Gia Vỹ
2018-11-25 01:37:24

So my first failed print happened earlier with this guy's left hand, supports didn't stick creating overhang and the skull successfully printed on top of the overhang. My guess is that the supports' top were too thin so it didn't hold properly, this is my second attempt with thicker support on that hand, any more ideas or criticisms?
Anycubic Green (0.03, 7.5, 4.5, 40, 8)

翻譯年糕

Ben Riggle
2018-11-25 01:42:32

Lưu Gia Vỹ
2018-11-25 01:45:14

Scott Mckay
2018-11-25 01:57:13

Alex Vee
2018-11-25 03:40:26

Ben Riggle
2018-11-25 07:06:54

原文網址 Gavin Rose
2018-11-25 00:07:18

As several of you have seen my loco prints you'll know by now I'm getting frustrated trying to NOT get lines in the prints. 90% of the time the line is 50% in the print whether it be a small 2mm scale N gauge body or a bigger 4mm scale body. At different orientations too...the line persists. Other than that quality is great.

Any ideas what to try next? Orientation angle seems to do bugger all. :(

翻譯年糕

Rick Beaty
2018-11-25 00:41:27

Chip Van Gilder
2018-11-25 01:00:25

Gavin Rose
2018-11-25 01:01:56

Phil Harpham
2018-11-25 01:11:33

Gavin Rose
2018-11-25 01:14:14

Gavin Rose
2018-11-25 01:16:01

Gavin Rose
2018-11-25 01:16:55

Gavin Rose
2018-11-25 01:17:08

Gavin Rose
2018-11-25 01:17:47

Andreas Karampatsos
2018-11-25 02:17:27

Gavin Rose
2018-11-25 02:36:29

Andreas Karampatsos
2018-11-25 02:58:28

Tom Bell
2018-11-25 03:24:10

Gavin Rose
2018-11-25 03:46:55

Alexander Zhang
2018-11-25 05:49:21

Gavin Rose
2018-11-25 05:51:06

Gavin Rose
2018-11-25 05:51:46

Alexander Zhang
2018-11-25 05:53:34

Gavin Rose
2018-11-25 05:57:27

Alexander Zhang
2018-11-25 06:01:33

Gavin Rose
2018-11-25 06:02:35

Darron Rodrigues
2018-11-25 06:22:01

Gavin Rose
2018-11-25 07:15:51

Brandon Kerr
2018-11-25 15:53:56

Gavin Rose
2018-11-25 15:57:58

Darron Rodrigues
2018-11-25 16:19:20

Sterling Osment
2018-11-25 17:47:16

Gavin Rose
2018-11-25 18:05:18

Darron Rodrigues
2018-11-25 18:38:38

Darron Rodrigues
2018-11-25 18:53:20

Leonard Seeney
2018-11-25 19:20:21

原文網址 Jose Antonio
2018-11-24 23:32:41

Tjank you for add me.
So...somebody have been testing this resin
https://www.amazon.es/ELEGOO-Resina-Rápid…/…/ref=mp_s_a_1_1…
Thank you

翻譯年糕

Marat Bedoev
2018-11-25 00:04:00

Jose Antonio
2018-11-25 03:29:27

Frank Kincell
2018-11-25 06:08:57

Austin Karl
2018-11-25 06:16:07

Jose Antonio
2018-11-25 06:21:58

Jose Antonio
2018-11-25 06:22:20

Austin Karl
2018-11-25 06:24:49

El Ner Endem
2018-11-26 06:31:29

原文網址 Dave Williams
2018-11-24 23:27:12

My fist print, I received the printer yesterday, took 15 minutes to unpack, check, setup and load my pre prepared file....have a look. I removed all supports, light sand and grey undercoat, this is the best printer I have used, simple and effective

翻譯年糕

Zena Andreou
2018-11-24 23:34:18

Thomas Wright
2018-11-25 01:23:54

原文網址 Jannick Langfahl
2018-11-24 21:19:36

2 Minute Luxury Anti-Squeak Fix
I got headaches from the squeaking the photon made, especially downwards was a pain. See the videos.
The fix I have in place now is guess what a zip-tie, around the rail and the rod.

I needed to re-level my plate as it turned slightly, took the machine apart on that occasion was about to do the wobble fix but couldn't even loosen the screw. Oiled the rail guides and the rod, put everything back together. Made sure the slider is fixed when the whole and the rod align most centered. No luck, still the squeaking, hence this quick fix. Can please someone make a rail endplate with some use, e.g. make a step down to the rod and put a guiding hole for the rod there, or to fit a teflon sleeve or something, I have no time.
Maybe this helps someone.
Good luck

翻譯年糕

Simon Chard
2018-11-24 21:25:22

Martin Jensen
2018-11-24 21:47:28

Jannick Langfahl
2018-11-24 22:23:16

Jannick Langfahl
2018-11-24 23:44:13

Jannick Langfahl
2018-11-25 09:40:21

原文網址 Bhavik Gohel
2018-11-24 21:11:44

Anyone have burnout temperature vs time graph for anycubic green resin?
Though resin is non castable,but from attached image, more detail can be achievable with controlled process parameter.

翻譯年糕