Anycubic Photon Printer Owners 造訪社團

原文網址 谢信福
2018-11-24 18:00:30

Sen Kun
2018-11-24 18:24:29

Gerhard Wilkens
2018-11-24 21:14:48

Richard Burrell
2018-11-25 00:38:12

Sean Poeschl
2018-11-25 01:20:43

Scott Young
2018-11-25 01:55:34

Scott Young
2018-11-25 02:04:19

Kennon Whitehead
2018-11-25 02:23:49

Dani Corado Quirós
2018-11-25 02:54:36

Kevin Johnston
2018-11-25 07:51:38

Zena Andreou
2018-11-25 17:54:04

Peter Ede
2018-11-25 20:06:12

Guido A. Mandorf
2018-11-25 22:41:28

Gerhard Wilkens
2018-11-25 23:16:19

Guido A. Mandorf
2018-11-26 01:57:58

Sen Kun
2018-11-26 02:06:02

Marco Acquaioli
2018-11-26 02:09:14

Sean Poeschl
2018-11-26 02:30:31

Richard Shapiro
2018-11-27 08:45:23

谢信福
2018-11-27 11:04:58

谢信福
2018-11-27 11:06:27

Richard Shapiro
2018-11-27 11:11:38

原文網址 Роман Хариков
2018-11-24 17:35:38

Hi! After washing in ethanol and exposure to ultraviolet lamp bottom part became a curve. Immediately after printing everything was fine .. Washing in water was not done. What could be the problem?

翻譯年糕

Роман Хариков
2018-11-24 17:59:17

Savio Ku
2018-11-24 18:02:23

Mantas Aus
2018-11-24 18:39:55

Alexander Volodin
2018-11-24 20:01:42

Sen Kun
2018-11-24 20:22:32

Darron Rodrigues
2018-11-24 21:35:18

Sen Kun
2018-11-25 02:26:57

Vinicius Silva
2018-11-28 01:54:33

原文網址 Ohad Daya
2018-11-24 17:22:29

Started to use the Wanhao Resin (dark green)
The first layers not sticking very well on all sides
My config is
0.05,8,2.8,65,15
Tried with also with 0.05,15,1,60,12 which gave me the same result
The bed seems to be balanced

翻譯年糕

Savio Ku
2018-11-24 19:48:38

Graham Leek
2018-11-24 20:00:10

原文網址 Adam Watts
2018-11-24 16:18:34

Looking for a resin that can withstand 220F. (I'm setting up models for vulcanized molds). Will the standard anycubic stuff work? I can't find the spec for heat.

翻譯年糕

Julia von Pfaler
2018-11-24 16:40:10

Adam Watts
2018-11-24 17:11:10

Joshua Payne
2018-11-25 07:36:03

Adam Watts
2018-11-25 08:46:53

原文網址 Dani Corado Quirós
2018-11-24 15:38:27

Finally my first print attempt sliced with ChiTuBox came out, but just the supports... ? Guess I missed something on the software settings, maybe the top contact depth was at its default value (0,1) to low ? Does that make sense? It shouldn't at a 0.05mm z res, but that's the only thing that comes to me...Help als always appreciated!

翻譯年糕

Fred Breton
2018-11-24 16:05:19

Fred Breton
2018-11-24 16:05:27

Fred Breton
2018-11-24 16:05:34

Fred Breton
2018-11-24 16:05:39

Fred Breton
2018-11-24 16:06:16

Dani Corado Quirós
2018-11-24 17:22:30

Stefan Giudici
2018-11-25 01:21:22

Dani Corado Quirós
2018-11-25 02:09:55

原文網址 Mark Weller
2018-11-24 15:09:41

Today’s Print!

翻譯年糕

Mark Weller
2018-11-24 15:10:53

Giancarlo Arriola
2018-11-24 15:23:02

Jaco Norchie Nortje
2018-11-24 17:01:57

Kevin Hull
2018-11-24 23:04:33

Kevin Hull
2018-11-24 23:05:17

Mark Weller
2018-11-25 00:22:47

Didier Dogliani
2018-11-25 01:18:01

Scott Mckay
2018-11-25 01:32:18

Mark Weller
2018-11-25 03:27:40

Giancarlo Arriola
2018-11-25 03:53:54

Mark Weller
2018-11-25 05:53:20

原文網址 Lưu Gia Vỹ
2018-11-24 14:38:00

Hello everyone, is it normal for this kind of file to have a 15-hour print? (the highest is the owl-bear, around 80mm tall).
If you guys have any advice regarding the setting or supports please feel free to leave a comment, it's my 2nd print and I'm still learning a lot :D