Anycubic Photon Printer Owners 造訪社團

原文網址 Stephen Francik
2018-10-01 06:38:14

Just got my Photon setup! What do you all recommend for a first print? I know it comes with the cube on the usb drive but that isn't very exciting.

翻譯年糕

Angie Angie
2018-10-01 12:15:00

Gabriel Brockman
2018-10-01 16:49:22

原文網址 Nicholas Gordon
2018-10-01 06:12:04

Does anyone else notice the "pop" sound of the print peeling off the FEP occurs slightly after you hear the z axis start moving? I would think the pop would happen instantly but I guess it's the FEP stretching a tiny bit.

翻譯年糕

Trea Cotton
2018-10-01 06:14:00

Alex Vee
2018-10-01 06:20:52

Khursheed Anwer
2018-10-01 16:45:58

Garret Bertrand
2018-10-01 22:49:59

原文網址 Alex Chapman
2018-10-01 06:00:15

Ok so anyone get this problem? I leveled just fine and the print holds just fine but then it's as if the screw that keeps the build plate is not secure (I've tightened it fairly decently to where I can't turn the Alan wrench with my hands anymore) and when the plate pulls up from the FEP the portion that sort of pops off causes the build plate to slowly shift out of alignment. Do you think I have my cure time set too high? 0.03, 12, 1, 65, 12. I'm gonna take it apart completely and retighten everything to see if that helps as well.

翻譯年糕

原文網址 Will Horner
2018-10-01 05:53:19

I have a little of the green any cubic resin left in the tank, not enough to complete my next print, but enough not to waste. can I mix it with monocure grey? I prime everything anyway so appearance really doesn't matter.

翻譯年糕

原文網址 Alex Vee
2018-10-01 05:44:15

Going for a pretty full build plate.... Printer Gods be with me! Going for a pretty full build plate.... Printer Gods be with me! 翻譯年糕

原文網址 Ohad Daya
2018-10-01 05:36:54

Hi
Started to print the test cube
I’m watching it now and i see the cube is broken on some areas, what does it means ?
Is it because the z=0 is too low ?
Thanks

翻譯年糕

原文網址 Jordan Marsh
2018-10-01 05:31:16

I need to print a large, not very detailed object. Was wondering, is 0.05mm the largest layer height I can print at or can I do 0.1mm possibly?

翻譯年糕

Fred Breton
2018-10-01 05:33:33

Stefan Giudici
2018-10-01 05:34:46

Jordan Marsh
2018-10-01 05:35:05

Jordan Marsh
2018-10-01 05:35:23

Stefan Giudici
2018-10-01 05:35:35

Fred Breton
2018-10-01 05:36:04

Fred Breton
2018-10-01 05:36:34

Jordan Marsh
2018-10-01 05:37:17

Stefan Giudici
2018-10-01 05:39:55

Mark Wardle
2018-10-01 05:45:13

原文網址 Martin Howell
2018-10-01 04:26:36

Just finished a print, cleaned and zero'd, but the plate won't move.

Tried going up and pressing home, but it makes noise like its trying to but doesn't budge.

Switched it on and off, and there are no errors.

Any idea what is wrong?

翻譯年糕

原文網址 Laurens Franssen
2018-10-01 04:18:22

My 2th try worked out great (leveling was the problem). It's amazing and I love it ? !

翻譯年糕

原文網址 Cody Holland
2018-10-01 03:39:13

First print Failure! =( Any suggestions on fix? It looks like all of my supports failed. Its a mix of 25% Flex - 75% anycubic green. Also Platebond....which works too well..spent 10 minutes trying to get the pieces off and they still stuck. Medium Supports ...(sorry for shitty pix, my hands were covered in resin so boyfriend too photo)