Anycubic Photon Printer Owners 造訪社團

原文網址 Sam Washere
2018-09-12 16:25:03

Lego part with photon :)
STL : https://printabrick.org/bricks/30375cs0

翻譯年糕

Joseph Bushen
2018-09-12 16:36:48

Jozef Kiss
2018-09-12 17:11:41

Sam Washere
2018-09-12 17:12:37

Sam Washere
2018-09-12 17:13:05

Jozef Kiss
2018-09-12 17:14:30

Sam Washere
2018-09-12 17:15:59

原文網址 Jean-francois Lacassaigne
2018-09-12 16:19:20

Hi all,
need to print a hollow structure.
what's de minimum size of the drain hole i need to have to avoid print failure due to suction ?
thanks

翻譯年糕

原文網址 Anders Bruhn Pedersen
2018-09-12 16:08:37

Was gettin some small layerlines when printing her straight on the buildplate. Sadly most of the supports gabe up halfway when i tried putting her at 45 ?

翻譯年糕

原文網址 Philippe Maegerman
2018-09-12 14:24:06

Mads Mikkelsen & Floyd Mayweather models by vimwerk
45mm phrozen resin @ .025
I was hoping for a bit more details, it might be overcured just a little.
https://gumroad.com/vimkerk
Ensar Yanar Jun Wei Lee Sergio Albeiro Gonzalez Mendoza

翻譯年糕

原文網址 Yan Scso
2018-09-12 14:17:42

A bit puzzled by my second print test, you see all of the lines and a prominent one down between the legs and body. Is that Z Wobble, slicer issue, FEP, or just normal? I also added text on the photo on other issues, any suggestions?

Printed Hollow on default settings with Green Anycubic Photon resin

翻譯年糕

原文網址 Clint Primley
2018-09-12 13:52:22

Well, I'm at a loss. A few days ago I successfully printed the test cube. Today my printer starts up and the touch screen works, but the z won't move, the UV/LCD won't test, and the USB won't read.

I've tried restarting, unplugging, updating the firmware and short of cracking the thing open, I'm out of ideas.

If this sounds familiar to anyone, I'd love to hear your thoughts.

翻譯年糕

原文網址 Dennis Batol
2018-09-12 13:41:08

Finally done with the posing. I wish the print bed was bigger though to make him easier to cut up. I'll have to go back down to 8 inch print just so I can hide the cuts in the natural folds of his body.

翻譯年糕

Kenneth Dahl Pedersen
2018-09-12 14:14:19

Dennis Batol
2018-09-12 14:15:12

Kenneth Dahl Pedersen
2018-09-12 14:15:52

Benny Baconstrips
2018-09-12 16:13:22

Aaron Swickard
2018-09-13 00:50:15

Alison Friedlander
2018-09-13 03:10:36

Fred Williams
2018-09-13 06:23:55

Andres Francisco Baeza
2018-09-13 15:42:20

Dennis Batol
2018-09-13 19:36:56

Dennis Batol
2018-09-13 19:41:17

Dennis Batol
2018-09-13 19:41:55

Dennis Batol
2018-09-13 19:45:14

原文網址 Tim Perry
2018-09-12 13:25:45

So, I finally had a kinda victory...

I had two items on to print, one in the middle of the plate and one to the side. The one on the side printed fine, after weeks of emssig around. The middle one didn't print anything at all.
What sort of troubleshooting should I be doing?

Pic is of my buddies Tabaxi rogue named Padfoot that I printed

翻譯年糕