Anycubic Photon Printer Owners 造訪社團

I reached out to Anycubic and they have been gracious to send 5 random members resin. You have 48 hours to PM me your address so I can pass your names on to Anycubic.

The winners are:
Artur Fuste , Iñigo Rubio Rodriguez , Miroslav Fekiač , Kenneth Ripple , and Miguel Diaz Durany

As our 1000th member, Damien Scott , also wins some resin. I'm really excited to have Anycubic team up with this page for such a wonderful treat to the members. We have a few ideas for when we hit some other big milestones as well. :-D

Oh, and I totally forgot. Because Flint Read has been so active helping everyone out, I was able to get him a container as well.

Congrats to all the winners, and to Flint for being part of this inaugural drawing. And special thanks to Anycubic for helping make this happen for all of us!

翻譯年糕

Can the Photon use Blue Cast or castable resins ?

翻譯年糕

While the photon is down and being trouble shot through email with anycubic service department, i figured I’d fire up the fdm printer for a little Easter fun with the kids. They’re Cadbury egg holders. File came from thingiverse.

翻譯年糕

Oh boy... just did a big purchase and one of them is the photon. Should be here thurs or friday this week. The waiting begins...

翻譯年糕

Hello first print for me. ?

翻譯年糕

I ordered Fun To Do resin from the US distributor on March 10. I heard nothing from them until today, when after I emailed them about an ETA they canceled and refunded my order due to a lack of supply.

What other resin do you guys recommend for someone in the US around the same price? My only experience is with the Anycubic green.

翻譯年糕

Anyone know what the average volume for a standard 28mm miniature for D&D? Trying to figure out how many I could get out of a bottle of resin.

翻譯年糕

Are there any fast-cure resins that are strong and slightly flexible? I don't need it to be like rubber but something somewhat durable for mechanical parts. I see some flex resins listed on the spreadsheet but they seem to take an age to cure. How are the monocure and fun to do resins for strength?

翻譯年糕

Allow me to relate the first experience with my new Photon, which ended about one hour ago.
I leveled the build platform using Flint Read's recommendations - trapping the paper sheet between the screen and the platform rather tightly, and then backing off 0.1mm and then doing the z=0 thing.
Loaded the vat, tightened it in, poured the Anycubic green resin up to the 1/3 filled line.
Tried to print a small model I sliced and downloaded to the usb drive, but it would not start. I noticed that the square on the display was outlined in red, which means the file is flawed. Started printing the sample lattice cube instead.
Bumped the table the Photon was placed on two times during the 6 hour print, once at about 20% finished and again at 60% finished.
Getting anxious to set up the post-processing operation, I bumped the table rather hard. The print stopped at 91% and I could not figure out how to restart it, if it could to begin with.
Shut the printer off and removed the build plate and took it to the IPA container. Could not scrape the base of the model off the build plate with the plastic scraper. I did manage to scrape the lattice cube off of it's base, however. The base is still welded to the build plate as I type. The 90% finished lattice structure looked just fine but the "photon" banner trapped inside the cube was flawed.
I am blaming myself for not being more careful moving around the printer, but the way the model base is stuck to the build plate suggests that my z=0 setting is too close.
And looking in the vat at the bottom, there is a lot of resin stuck to the fep.

翻譯年糕

my photon just shipped from amazon for next day delivery. CAN'T WAIT! :D

翻譯年糕