Anycubic Photon Printer Owners 造訪社團

原文網址 Karl Trout
2018-03-17 20:43:31

Woke up this morning to this white version. Glad to know the settings used for grey work just as good for white with the 3D-OKAY resins. Only complaint is it’s harder for my old eyes to work with the detail on the white. Not enough contrast. I’m gonna assume the same problem with black.

翻譯年糕

原文網址 Flint Read
2018-03-17 19:01:18

Just finished a long and tall print to see if the slight wavy lines I had been getting in prints, had been solved by adding a diode based current smoother between the board of the photon and the motor and I am glad to say at 0.03 they seem to have gone 0.03 was a height that made them particularly visible for me and now im not seeing the phenomena (it looked like a very slight undulation peaking every 20 layers or so and was definitely not Z wobble)

Here is a link to the exact module i fitted
Don't be fooled by the description it's not a controller it's just a current filter.
Also if you fit it make sure to insulate it with electrical tape so the solder pads can't short out inside the case of the Photon.

翻譯年糕

Phil Dalbeck
2018-03-17 19:43:44

Grant Parkes
2018-03-17 19:43:46

Flint Read
2018-03-17 19:45:03

Flint Read
2018-03-17 19:56:17

Phil Dalbeck
2018-03-17 19:56:29

Flint Read
2018-03-17 19:57:35

Nel Elson
2018-03-17 20:23:07

Flint Read
2018-03-17 21:00:17

Flint Read
2018-03-17 21:05:38

Flint Read
2018-03-17 21:06:08

Flint Read
2018-03-17 21:10:23

Flint Read
2018-03-17 21:18:24

Flint Read
2018-03-17 21:18:33

Phil Dalbeck
2018-03-17 21:24:18

Flint Read
2018-03-17 21:26:02

Phil Dalbeck
2018-03-17 21:26:36

Phil Dalbeck
2018-03-17 21:28:01

Phil Dalbeck
2018-03-17 21:28:24

Flint Read
2018-03-17 21:29:26

Flint Read
2018-03-17 21:29:54

Flint Read
2018-03-17 21:30:27

Flint Read
2018-03-17 21:31:39

Flint Read
2018-03-17 21:31:52

Adam Albee
2018-03-17 22:23:51

Nel Elson
2018-03-17 22:33:41

Phil Dalbeck
2018-03-17 22:49:08

Phil Dalbeck
2018-03-17 22:49:52

Phil Dalbeck
2018-03-17 22:49:59

Adam Albee
2018-03-17 23:01:07

Vaughan Lundin
2018-03-17 23:01:10

Flint Read
2018-03-17 23:02:57

Phil Dalbeck
2018-03-17 23:06:05

Phil Dalbeck
2018-03-17 23:06:52

Flint Read
2018-03-17 23:07:48

Phil Dalbeck
2018-03-17 23:09:20

Flint Read
2018-03-17 23:10:12

Adam Albee
2018-03-17 23:11:45

Phil Dalbeck
2018-03-17 23:13:16

Jeremy Lauzon
2018-03-17 23:50:32

Phil Dalbeck
2018-03-17 23:57:02

Flint Read
2018-03-18 00:06:22

Flint Read
2018-03-18 00:06:54

Flint Read
2018-03-18 00:17:08

Phil Dalbeck
2018-03-18 00:18:26

Flint Read
2018-03-18 00:19:31

Jeremy Lauzon
2018-03-18 00:25:53

Jeremy Lauzon
2018-03-18 00:26:11

Phil Dalbeck
2018-03-18 00:27:26

Flint Read
2018-03-18 00:28:16

Jeremy Lauzon
2018-03-18 00:30:21

Flint Read
2018-03-18 00:31:16

Flint Read
2018-03-18 00:31:37

Jeremy Lauzon
2018-03-18 00:32:17

Flint Read
2018-03-18 00:33:10

Mariano Loisi
2018-03-18 04:04:06

James Rotondo
2018-03-18 04:49:01

Sa Rnd
2018-03-19 06:07:51

Mariano Loisi
2018-03-19 06:52:22

Toby Kirkby
2018-03-19 07:09:32

Sean Latto
2018-03-22 00:58:38

Sean Latto
2018-03-22 01:01:00

Flint Read
2018-03-22 01:04:37

Sean Latto
2018-03-22 01:05:25

Yosei Ikeda
2018-04-04 01:53:40

Flint Read
2018-04-04 05:59:00

Kaanaan Kuna
2018-04-04 07:22:09

Flint Read
2018-04-04 07:22:48

Kaanaan Kuna
2018-04-04 07:25:13

Flint Read
2018-04-04 07:25:17

Kaanaan Kuna
2018-04-04 07:29:50

Yosei Ikeda
2018-04-04 07:30:06

Yosei Ikeda
2018-04-04 07:32:13

Flint Read
2018-04-04 07:33:42

Kaanaan Kuna
2018-04-04 07:36:07

Flint Read
2018-04-04 07:36:33

James Rotondo
2018-04-04 10:14:13

Sean Latto
2018-04-07 23:47:46

Flint Read
2018-04-07 23:48:41

Sean Latto
2018-04-07 23:49:20

Flint Read
2018-04-07 23:50:40

Nel Elson
2018-04-07 23:56:06

Yosei Ikeda
2018-04-08 00:31:21

Markito Trogolito
2018-05-07 19:00:50

Lou Steinritz
2018-05-11 22:35:38

Lou Steinritz
2018-05-11 22:38:25

Lou Steinritz
2018-05-11 22:51:35

Yosei Ikeda
2018-05-11 23:38:32

Lou Steinritz
2018-05-12 00:08:16

Grant Parkes
2018-05-12 03:42:00

Lou Steinritz
2018-05-12 04:41:37

Markito Trogolito
2018-05-12 04:44:51

Nel Elson
2018-05-12 06:43:50

Lou Steinritz
2018-05-13 22:13:56

Vinicius Silva
2018-07-23 05:51:21

Vinicius Silva
2018-07-23 06:03:14

Anh Hoàng
2019-06-20 06:25:01

Martinus Hwit
2019-07-29 01:29:37

原文網址 Julia von Pfaler
2018-03-17 18:09:37

Here's my first test print, that didn't end up looking like a puddle. If there's not enough detail or if there's defects (like those small swirly patterns and a few lines caused by pausing) it's completely my own fault, trying to learn to use Zbrush and studying anatomy. Anycubic green resin: 0.05, 8 sec normal, 1 off, 60 sec base, 8 layers ?

翻譯年糕

原文網址 David Wong
2018-03-17 18:09:01

Just done with bitcoin.... ...Quick question, every 3d printer should print a benchy, so should I print a benchy too on Anycubic Photon? ?

翻譯年糕

原文網址 Lauri Eno
2018-03-17 18:04:10

Hello Phomasters. I received my printer yesterday. Looks pretty nicely built. Vat is sturdy and beautiful and build table is pretty impressive too (sturdy and straight). Linear guide/rail could be more sturdy but what can you except.. machine costs 430€ :D (feeling tempted to change proper linear guide to the machine (ball type)

I make jewelry so cast ability is only thing that interest me about resin. Gladly i found out that my old b9 creator yellow resin works fine with the machine. Couple failed prints before i found working settings. Layer thickness is 0.025mm and cure time 15s. Might need some tuning but at least it prints.

Tip of the day: The anodized bottom surface of the build table is pretty slippery and might cause failed prints. Remove the anodization with sodium hydroxide or other strong alkali. Removing the anodic layer opens the porous surface of aluminium and alkali slightly corrodes the surface for better adhesion.

Question of the day: Photon slicer: Is there any way to adjust the position of the part in the support tool.. I mean that the support tool always pops the model up and why the hell would i want to use my print time to create supports that i might not need... Second question: Have anyone tried other programs to make the supports and slicing?

翻譯年糕

原文網址 Thilo Gebhardt
2018-03-17 17:13:40

Ok, so first print failed, unfortunately - it just stopped halfway through!
I'm kinda lost, my best bet would be faulty .photon file, but would there be any way to check?

Has anyone else run into this?

翻譯年糕

原文網址 Roger Cejalvo II
2018-03-17 14:15:24

So I'm ready when i get my photon, what size FEP should i get for when i need to replace it? 50, 100, 127, 128, 150? These are the sizes available at fepshop. what is the default size that comes with the photon? and why would i use a different micron size then the default micron size? Thanks

翻譯年糕

原文網址 Grant Parkes
2018-03-17 14:11:06

So my 9yr old son came home yesterday and saw the new printer and green resin and all he wanted was the "HULK" so dad took up the challenge. Got a feeling I got to many supports (Comments Please!) Order parts are more practical for me.... Linear rail guides for my Anycubic Delta+

翻譯年糕

原文網址 David Wong
2018-03-17 12:30:04

9hour print. .. after prime it, every detail pop.

翻譯年糕

原文網址 Robert Maki
2018-03-17 12:13:04

Layer shifting... what do you think would cause it? FYI, I believe the layer that it shifted on, was basically the bottom of the keycap (not the bottom bottom, but right next to the stem...see other photo). I used maybe 4 light supports underneath there. I printed 4 of these and each one seemed to have the same layer shift at the same point.

翻譯年糕