ATOM 3D Printer Group 造訪社團

原文網址 林瑋群
2016-03-27 19:04:07

不好意思我想請問一下我因為列印尺寸有比例縮小所以我按照說明書上設定DELTA_DIAGONAL_ROD，調整完之後我就再跑一次結果其中一個滑軌就跑超低，低到撞到板子然後一直卡在那裡發出很大的聲音，請問是發生什麼事了.....（檔案室官方測試檔）

黃俊傑
2016-03-27 21:09:12

話說你重燒韌體完有先校正嘛？？？

李穆
2016-03-27 21:49:56

重傳完韌體要先按restore failesafe然後再按store memory，重開機後執行Autolevel之後才能印喔

林瑋群
2016-03-27 22:05:35

李穆我剛剛重新把最新的韌體灌進去重新跑，現在跑得很順，可是我剛剛沒有做“按restore failesafe然後再按store memory，重開機後執行Autolevel”的動作噎，這樣會怎樣嗎？？？

李穆
2016-03-27 22:34:28

沒做應該參數就不會更新到，關掉就沒了

黃俊傑
2016-03-28 09:18:05

稍微檢查一下噴頭微動吧有時候瀕零臨界點，剛剛好去碰到啥的就不會噠噠噠了...

原文網址 Estima Lin
2016-03-27 17:49:51

熱床破功？陽極鋁板表面一直重覆用的地方會愈來愈光滑！
原先一直鐵齒的以為有熱床都不用上口紅膠或藍色膠帶！
但是這個收縮不知道是什麼？我真的不想用口紅膠啊！

許阿瑋
2016-03-27 17:52:48

重複使用過的地方要清洗，越用越光滑到最後就會黏不住

黃俊傑
2016-03-27 18:57:51

改毛玻璃或者陽極處理板了...

Estima Lin
2016-03-27 19:26:51

玻璃導熱係數好像蠻低的？
我想上面再放一片不陽極的鋁板呢？

原文網址 Charlie Ting
2016-03-27 16:19:24

[FabScan / hardware]

雷射驅動、步進驅動、接線完成

軟體初步測試及修正完成（用 FabScan for Processing 版測試，又要學新東西～～XD）

感覺重點在於參數調整，才能取樣正確，後面算圖才有發揮空間，不然一切白搭。

王榮達
2016-03-27 16:26:26

開發掃描器？

Charlie Ting
2016-03-27 17:37:58

Shu Tseng
2016-03-27 17:57:42

有辦法利用像是 kinect或是RealSense 那種不可見光的發射器及接收器嗎?
畢竟這雷射光會刺眼(?

原文網址 Noel Singson
2016-03-27 16:11:53

Aside from the 100k thermistor, are there other consumable parts I should stock up on to reduce downtime?

翻譯年糕

Clarence Lee
2016-03-27 17:58:15

another spare hotend ;p

Noel Singson
2016-03-27 18:24:08

Hahaha I was afraid someone would say that.

Clarence Lee
2016-03-27 18:56:46

When you are maintenance your hotend, you would like to install another when your are working on it. Much shorter down time.

Birk Binnard
2016-03-27 23:16:54

PTFE tubing for inside the hot end. It is 3/2 mm OD/ID. Nozzle jams are usually the result of crystallized plastic stuck on the inside of the tube, or sometimes the tube just getting burned.

原文網址 Shi Xinhui
2016-03-27 14:59:13

終於搞定了熱床啦～xy軸加了led燈條把上次進料機下移的線也整理乾淨總共花了我兩個週末日但還挺樂在其中的

陳健誠
2016-03-27 15:13:20

有雷鬼風格!!請問一下，把進料馬達往下移有什麼優點??

李穆
2016-03-27 15:16:58

ATOM的樂趣就是改裝啊！

Bise Chen
2016-03-27 15:18:41

那個LED，為何不是照亮列印物而是往外面照？

陳為騰
2016-03-27 15:50:51

燈條電源要接那裡呢？

姜智勻
2016-03-27 16:02:35

美

王大雄
2016-03-27 18:59:55

請問底下圓盤座要如何改裝？原廠做的真不優呀!

陳明谷
2016-03-27 19:06:06

好奇哪裡不優

RenJie Huang
2016-03-27 19:15:14

打燈好帥，應該要多一點顏色，底版也要發光

原文網址 Shi Xinhui
2016-03-27 13:06:26

又卡料…不知其他方法下的我又第二次拆了噴頭在辛苦的搞定鐵氟龍管後正準備復原時斷了… 是在強迫提升我修噴頭的等級嗎…

曾荐宏
2016-03-27 13:19:41

只要加温到240，再用最小的六角板手通一通即可

李建德
2016-03-27 13:24:28

我改用這個熱敏電阻直接從側邊放進去就好了

葉世瑋
2016-03-27 13:27:10

Cadmus Zeng
2016-03-27 13:29:34

沒關係，我也是苦主

廖新弘
2016-03-27 13:38:12

就是必經之路，順手的話，前後不到三分鐘搞定

李穆
2016-03-27 15:15:51

換過這個就所向無敵了

Shi Xinhui
2016-03-27 16:32:05

話說新版韌體的換料功能還不錯說

原文網址 Birk Binnard
2016-03-27 08:08:20

WiggleLamp4

This lamp is similar WiggleLamp3, but has more and wigglier wiggles, and the wiggles have rounded curves instead of sharp edges. The lamp can accommodate either a multi-colored LED light kit or an all-white one. Here are links for both kinds of lights:

http://www.amazon.com/gp/product/B00R7F7PNQ…

http://www.lowes.com/pd_406110-43768-NS511-R6-306_1z0y4gqZ1…

I printed WiggleLamp4 with yellow PLA, and to ,my surprise it works well with either the white or colored LED. The first photo shows the lamp with the LED off, and the others show how it looks with the LED set to different colors. Here is a short video of the LED changing colors by itself:

https://www.youtube.com/watch?v=nHG2qhZjtMU

The STL file is here:

http://www.thingiverse.com/thing:1445270

This print took a little over 30 hours with a layer height of 0.200 mm and a print speed of 55 mm/sec. For this print I changed Retract from 6 to 5 mm and increased Acceleration from 700 to 1100. The printer was still noticeably smoother and quieter than when I had Acceleration at 2000, so it looks like 1100 is a good compromise. However, there was some stringing on the inside of the part, so I am changing Retract back to 6 mm.

翻譯年糕

原文網址 Harry Cayne
2016-03-27 03:02:14

Hi, is it possible to change the bed leveling limit switch from normally closed to open in the software ? I am trying to make a new type of printing head with more switches connected together for sensibility and only with normally open is possible . Thanks

翻譯年糕

Clarence Lee
2016-03-27 08:58:02

configuration.h
const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.

原文網址 Chiufan Luk
2016-03-27 01:50:27