ATOM 3D Printer Group 造訪社團

2.0.4 Update notes:
修正雷射模糊問題
增加雷射微光功能: 於BURNER中選擇Console輸入M04即可啟動微光功能

猜測是版本顯示跟校準值自動儲存吧

M04應該是起頭定位用的,因為某個雷射頭就有這個功能

2.0.4 更新兩次？

因為前一次忘了改版本名XDD

強度會不夠

原廠的也是塑膠做的而已.....我是這樣想的

如果可以處理好接縫處與做好漏水處理或許還蠻有趣的，不過花的成本應該會超過購買價格喔

漏水可能就是命一條

真空翻模

一台 30 公斤來算, 要 50 卷一斤裝的 PLA, 一卷 600 元計光材料就要花 3w .... 的確不合算

應該可以，只是很貴

除了強度不夠,就算下水沒沉,水會從各個連接縫造成阻力,划起來會超累,且列印件沒經過處理,是沒有水密性的.

國外已經有人印過了 https://youtu.be/odmFO7pJ-RQ

在這之前可能要先印個救生衣

我是漫畫版的黑色

最後一天報名囉！請把握機會

真的獲益良多！謝謝高手指導

這花印的好漂亮~~~

馬上歪樓

是阿，這花是我用新買的atom 360印的, 層高0.1奈米，full color

尤達大師的新髮型⋯⋯

玉蘭花漲價了 0.0 本來三串50元，今天變兩串50元 0.0

導線?

現在拿去印印看

放魚竿的

釣魚打發時間畫的圖...

烤魚架(來亂的)

炮火發射台（誤

膠帶台？

答案揭曉 ......

zoom in

還滿好用的

好酷啊!! Mickey大可以跟您要檔案嗎？
小弟也有在釣魚

3D列印機=產品製造機

如果高比底面積比例大
建議開brim
你已經發現氣溫是重點了 …… 查看更多

貼參數看看比較準

機器加熱，手動送料，看送料順不順，先確定送料是否正常

送料入口削削太多(料太差或太頻繁回抽)與底盤沒黏緊
我都會這樣~

目前是kisslicer是設定 9-9suck-5wipe，之前試過8-8-5與7-7-5都不會～原廠料建議的設定值是多少

請各位給我一些建議

1. 關閉 prime pillar
2. prime/suck < 5, wipe 0, min jump 5, trigger 15
3. temperature 210(因為現在偏冷) …… 查看更多

感謝各位前輩賜解～晚上來試跑

有點搞剛這東西... 沒法選其他機型的樣子！

Windows version not available yet.

還好我用雙系統~!! 等等來玩看看~!

I think all you have to do is slide the tube in as far as it will go and then reassemble the nozzle. As long as you have the inner chamber cleaned out you should be OK. The metal piece that screws into the top of the nozzle has a small ridge on the in side top that holds the tube in place.

I vaguely remember someone saying the tube inside the nozzle should be about 34 mm long - but it might be 43 mm.

Edit: actually it is 23mm long

Yeah but I can slide it in without any resistance. Holding my finger on the edge where it slides in and then pulling it out lets me see, that the tip of the tube is near the nozzle. This is where it stops. My old tube (which melted) cannot be pushed in as far as the new one. This is why I was wondering, because when I push it in to the tip, won't it melt again on my next print?!

I see what you mean. That is a good question. In my case I pushed the tube in as far as it will go and so far I have no indication that it has melted.

I vaguely remember reading somewhere that the PTFE material can tolerate temperatures up to 400C, so if that is true there should be no problem. But I guess the only way to tell for sure is to test it.

Good luck!!

Well, i put it in now and it does print...
Now my steel balls and the rods start making noises.. won't those problems ever end?
What kind of lubricants do you guys use?

I use white lithium grease. It comes in large tubes and seems to work OK. I put a small amount on the balls with a Q-tip and spread it around as evenly as I can.

I think that if you can spin the rods while they are all connected and not feel and roughness or stickiness the joints should be OK.

PS: I just measured the length of the PTFE tube inside my hot end and it is 23mm long.

Does it reach up to the hotend? Its working so far. Only Problem I have... He suddenly stops printing a layer and then does it again. Or he prints it very thin which results in not stable parts. You can nearly tear them apart by hand... Any Ideas on this one?

I am having the exact same problem as you and the best I can determine is that the cause is either a clogged hot end or a problem with the extruder. I am still working on a specific diagnosis.

Funny fact: Printing those parts in Single prints results in no problems.

Okay and here is - of course - another one I really don't get.
I print 5 parts, everything fine. I start the sixth - and suddenly it stops printing in the front. The distance between the nozzle and the printing bed is too far, so it can't lay down the filament. Another Auto-Leveling didn't bring any success.Any Ideas on this one?

sound like retract problem, since multiple prints required retract when moving between objects.
try retract less length

Any photo to identify area on bed?

8mm at 100mm/s... at about 10mm he retracts it so far that he sometimes cannot deliver any more and just move without extruding.

As my gf sleeps right now, can't start the printer now. Got the ruined part (which is folded in the midde as you see on the line) out of the trash and put it on the spot where it was. On the tip in the front you can see that it got ruined because there was no adhesion to the bed. Can make a video tomorrow

http://www.thingiverse.com/thing:15087

Printing right now, this time it doesnt crash because of it. but you can clearly see how the skirt wasn't laid down the right way and the front of the part also. Now it looks warped although it never had contact to the printing bed...

Pic nr 2