ATOM 3D Printer Group 造訪社團

所以神油以後沒有的意思嗎？

算一算集資贈品的金額... 賺到 XD

真的賺到。

神油點進去是缺貨中...

還好我看到就馬上下單了

也太快了ㄅ

我比較想要膏版的也，油不好控制。雖然用筆還可以啦，但自從我把印表機裝到櫃子後，有兩面我都塗不太到。XD。

買不到油…

神油變神油膏那還點的進滑塊的注油小孔嗎？

應該只能塗在滑軌上

我是印了一個柄，插一塊海綿來塗黃油，塗完以後滑塊滑個幾次就吃進去了

舊油不擠出？

其實我覺得膏狀的油滿耐用的...我上一次油，印到目前還沒有需要補油的感覺
球頭的部份我當初是直接挖一小塊塞在連桿的洞裡面

其實有油嘴的，應該是要打入新油擠出舊油，換掉含有鉄屑的舊油，沒有油嘴的就當消耗品，出問題就整個換了⋯⋯

求教學

我願付費買app，但是我的是ios系統也，有辦法嗎？

真神人！！！ m(_"_)m

好厲害阿~~

又有神人出巡了（跪）

不得了呀....

原廠快來收購!

神丫...........跪........拜..............
這一定要寫個教學文..........

有需求~~非常需要這種功能

容許我們叫你一聲大師

已膜拜+訂閱(_ _)

又有位神人級之一
（膜拜

將鋼骨的外觀收斂於特製的機殼之下， 除了增強穩定度之外， 更預留了封閉外罩的擴充空間

老實說，自從裝了盔甲，感覺都不一樣了。

果然佛要金裝，人要衣裝，ATOM要盔甲裝

真得整個霸氣!隨便印都很漂亮哈

這裝了的用徒是？

需要的是封閉外罩，但又有人說想防塵不如買櫃子裝，究竟有沒有人盔甲裝了外罩的...貼個圖...

想想都覺得搞剛

請問一下官方釋出壓克力圖擋了嗎?

我想試試看用克潮靈, 跟料放一起放在密封箱中

微波爐，強火，反覆加熱、冷卻，每次加熱10~15秒就好，不能熱到融了哦。

只是我很納悶....塑膠為何會受潮阿>"<

我都放防潮箱，過一陣子又很好印了

土法煉鋼報告~~~目前曬完太陽收回來列印中~~~似乎一切看起來都很順利中~~~^^

電子防潮箱+1
好像放不下了，看樣子又要再添購一台～

所以大家不印都乖乖卸料放防潮箱嗎？
我這樣好像太偷懶了，快兩週沒印就給他放在料架上⋯（抖

看環境跟看料性吧;p

最後....還是堵料失敗了...看來真的需要買防潮箱了>"<

也可能是參數問題,噴頭狀況等變數...得逐一排除...

參數應該沒問題....之前印都沒事...而且環境都固定開冷氣26度下去印的.....

14捲要怎麼放進去......

可以先測試手動進料 找出問題點 !

Here is how the part looks at height Z = 2.50. I think it will finish printing OK, but with a bumpy bottom surface.

M503 via pronterface , check your G29 array.
Might be a clue about it.

Thanks Clarence - the print has several hours to go but I'll try your suggestion after that.

I see that M503 lists the printer's firmware settings. I expect I won't be able to understand what these are or mean, but we'll see.

G29 talks about printhead Z offset. I did specify G29 Z+0.6 in Craftware's GCode preset section. Perhaps this is related to the problem.

I had to abort the print because one side of the part lifted off the printbed. Since it was the side where most of the bumps appeared I'm quite sure they were the cause. Since I've been using blue tape I have not had a single occurrence of parts liftin g off the printbed, and I have printed some fairly large pieces.

I did run the M503 command and got the following results for the bed level matrix:

Bed Level Matrix :
RECEIVED: -11.675 -11.675 -11.675 -11.863 -12.113 -12.113 -12.113
RECEIVED: -11.800 -11.800 -11.913 -12.050 -12.206 -12.388 -12.388
RECEIVED: -11.950 -12.031 -12.138 -12.238 -12.331 -12.450 -12.569
RECEIVED: -12.188 -12.275 -12.350 -12.400 -12.425 -12.438 -12.500
RECEIVED: -12.244 -12.431 -12.488 -12.531 -12.563 -12.544 -12.500
RECEIVED: -12.481 -12.481 -12.588 -12.644 -12.638 -12.631 -12.631
RECEIVED: -12.575 -12.575 -12.575 -12.725 -12.769 -12.769 -12.769

These numbers look fairly consistent to me, but of course I have no idea what they are supposed to be.

I'm going to make the part smaller and try reprinting it. Will be interesting to see what happens.

I recall having the same problem with too high Z-compensation. 0.6 is a lot. Try making it smaller and also decrease print speed on first layer to about 60%. Use gluestick on top of blue tape. The gluestick has one other good property; it eliminates silicone og grease marks on the tape (or any other surface). Also beware of too cold print temp. Stay at 200-210 degrees. Hope it works.

Because you have new blue tape for this print, so your z-offset is sightly changed.
You may change G29 Z+xx for a smaller value, or do G29 about 3 times, then start the print.

Yep, you are printing on air!

You may notice after you do G29 several times, the blue tape will have many tiny holes at these calibration points. That will make you have different z-offset for new and old blue tapes.

Thanks for the feedback. I'm about 55% done with printing a smaller version of this part. It had that same problem but the bubbles were more centrally located. I thought that might be enough to keep it from un-sticking, but I see that one side has be come un-stuck anyway. Nevertheless I am going to let it finish printing.

I've got 2 methods in mind for dealing with this issue:

1. I saw a video that suggested a good way to ensure build plate adhesion was to sand the surface of the plate with 100 git sandpaper. I have an orbital sander so after this print is finished I am going to do that to the unpainted surface of the build plate.

2. If #1 works no better I will order a Zebra plate.

My understand was that a G29 command stored the current bed position in EEPROM and therefore did not have to be repeated unless something physically changed with the printer or bed.

Maybe I'll be able to do away with the blue tape and thus eliminate on variable in this overall configuration.

The problem may not solved by Zebra Plate, since it's possible cause by the G29 might didn't probe perfectly on your current setting. (BTW, don't preheat running G29 when it's Zebra Plate, it hurts the plate)
http://www.maui-3d.com/cgi-bin/plotG29?plotG29ID=5355

Tuning G29 Z+0.6 lower might be a start, or try to let bed higher at y tower position.

正常的，我的也是這樣

看了真不爽啊 ? ? ? ?

可以拆下來扳平一點，雖然功能性沒差多少

板上有人用啤酒罐的鋁皮自製 XD

那25mm風扇的螺絲是鎖不緊的嗎？

塑膠螺孔，沒有螺母的設計，一直轉的話會.....

扳平一點就好囉

我的也一樣歪歪的，算是它的特色了

之後再印導風板鎖在上面，改善出風效率，這樣也可以遮掉那違和感。

這樣其實對於氣流的螺旋形流動有幫助

謝各位大大 ☺
那集線管需要剪的嗎？

我的是沒剪，和電線的長度剛好配合，只是總覺得好長

我自己在安裝的時候，所有東西都沒有剪，反而覺得官方把東西全部設計到一點緩衝空間都沒有，感覺超級難安裝。 但是安裝完之後就超有成就感。完成安裝後，更是覺得沒有東西是多餘的!!!

美女的手有加持擠出頭的效果

嘿…

擋風板會歪歪而且開開的是因為你的後風扇卡到側風扇了…看是要修改後風扇或直接把檔風板撐開吧…

比較好奇上方是襪子嗎? XD

這個歪歪的算正常，除非你自己把它扭一下就會比較正。看在不在意了～～～我是裝起來之後就不想拆了。

我有直線強迫症 哈

照片中你的右側風扇下方跟三角外框快接觸到了，要調整一下，否則作平面校準時會出包

對 ? ? ?

側面照可以拍來看看嗎

襪子是特工嗎

我的好像更大問題!救求！！

怎麼了

有人有用過copperfill的料嗎？ ?

原廠後風扇應該是可以直接把下方不鎖螺絲的孔整個削掉，我的原廠後風扇還沒使用過就被我搞壞了，所以圖內非原廠…

消失了

我直接拆掉部用....應該不影響功能吧,我想

聖誕節 襪子應景

後面那尊很威的感覺....^^

感覺樓主又是一位潛水神人

各位才是，我是位老實人哈哈

懂了！老實的神人！

低調的神。。

充滿螺旋力的摩艾

還在思考怎樣才能去除螺旋power

都是出現在往外擴張的表面，摩艾的話就是後腦勺、下巴、眼窩，其他地方都很好

太晚了開印會吵到家人，如果你沒這問題可以拉高溫度10度，速度上到15～20先試試看，期待你先分享成果

所以我猜女體的南半球跟屁股下方應該也有一點螺旋力？

沒錯！如果可以每一層都反向列印也許就可以解決了，還在想怎麼從Gcode下手解決

大家都愛摩艾

這是軟料?摩艾的下巴搞定了?

還沒，被螺旋力轟炸中

看起來有改善一點，等拆下來好好研究

現在溫度210, 16mm/s

稍稍改善而已，螺旋現象還是存在
看那個光的路徑就知道被拉多長。

長頭髮了 0.o?

這個胸部真是漂亮呀, 阿...我是說模型啦

阿他的比基尼哩…

感覺不錯

神人

我比較好奇, 那個3M是做什麼用的呀

大家都用軟料印這尊XD

[研究課題] 重複印之後發現會產生螺旋狀的紋路，等明天來測試捉高溫度提高速度的方式看能否改善，版上各位神人如果有解法也希望能分享一下

居然還有vP和vS可以設定，這就是傳說中的kisslicer pro版嗎?

我也有注意到，好想調看看。

這是1.5beta2.22版，不用開通pro key也可以設定vP vS。
https://www.dropbox.com/....../AABau30kpAP2BEY1tffRFeG......