Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Víctor Almela
2019-11-11 21:46:54

Hi folks,

I upgraded firmware to 4.2.18, does it have Antialiasing?, in order to use AA just I need to check box in Chitubox?.

Last question, enabling AA increases print time?, I see 4x and 8x values, is there much difference in speed and quality?.

Thanks in advance.

翻譯年糕

Sen Kun
2019-11-11 21:57:20

Víctor Almela
2019-11-11 21:58:32

Sen Kun
2019-11-11 22:00:20

Víctor Almela
2019-11-11 22:09:02

Sen Kun
2019-11-11 22:10:15

Víctor Almela
2019-11-11 22:44:50

Sen Kun
2019-11-11 22:46:58

Víctor Almela
2019-11-12 02:21:27

原文網址 Víctor Almela
2019-10-28 21:41:19

Hi guys,

I downloaded latest Photon firmware (4.2.19) from Anycubic's website and I uploaded files to USB (2 files). I plug USB into printer and power it on, I see the USB lights reading for about 10 seconds and then the printer screen starts. When I browse USB content to print both files I don´t see anything. The same happens in 2 different Photons I own, both with firmware 2.18.

*I have sound disabled in printer so I don´t hear any beep during upgrade.

翻譯年糕

Dan Andersson
2019-10-28 21:42:41

Tiernan Messmer
2019-10-28 21:44:14

Jeff Greenfield
2019-10-28 23:50:06

Víctor Almela
2019-10-29 00:03:35

原文網址 Víctor Almela
2019-10-26 05:37:33

Hi guys,

Releveled plate today after minor sticking problem on one short side and then printed again and found a huge crack in the bottom layers. First ones look leveled but then appears the gap.

Printed in fresh bottle of anycubic grey resin.

Sliced with default Photon program.

Printing settings:

Exposure: 10s
Bottom layers: 6
Bottom exposure: 90
Off time: 6

Any advice will be greatly appreciated ? .

翻譯年糕

Victoria L. Cordone
2019-10-26 05:50:33

Jared Davis
2019-10-26 12:05:20

原文網址 Víctor Almela
2019-09-12 02:26:44

Stupid question folks...is firmware 4.2.19 from official source the recommended one? I prefer to ask cause sometimes latest firmware is buggy ? .

翻譯年糕

Vinicius Silva
2019-09-12 02:29:27

Douglas Rector
2019-09-12 06:30:30

Víctor Almela
2019-09-12 14:12:06

Víctor Almela
2019-09-12 14:12:44

Vinicius Silva
2019-09-12 16:45:28

Víctor Almela
2019-09-13 05:08:33

Víctor Almela
2019-09-13 06:26:24

Vinicius Silva
2019-09-13 06:36:41

Víctor Almela
2019-09-13 13:45:31

André Nettermann
2019-09-13 22:11:40

Jarrod Smith
2019-09-13 23:32:29

André Nettermann
2019-09-13 23:41:40

Jarrod Smith
2019-09-13 23:51:29

Víctor Almela
2019-09-14 02:49:26

原文網址 Víctor Almela
2019-09-03 02:58:41

Hi guys,

Any recommended value for “off time” in photon slicer? I’m using anycubic grey resin, thanks.

翻譯年糕

Paul Fagan
2019-09-03 02:59:56

Juan Camilo Herrera
2019-09-03 03:01:00

Jay Raven
2019-09-03 03:07:31

Max Dercum
2019-09-03 03:17:32

Chad Elstad
2019-09-03 03:22:29

Víctor Almela
2019-09-03 03:40:59

Chad Elstad
2019-09-03 03:43:56

Booga Kabuto
2019-09-03 03:58:37

Mark Wardle
2019-09-03 04:01:32

Víctor Almela
2019-09-03 05:00:28

原文網址 Víctor Almela
2019-06-20 20:34:07

Hi guys,

I see that there is an antialising feature for the Photon and a beta firmware on Anycubic site for enabling it. They mention you need to use Chitubox for slicing instead of default software.

I see also that the latest Validator has antialiasing feature too. Can I use default slicer without AA and later activate it on Validator? or is better to use Chitubox directly, this is new program for me so I´m lost.

翻譯年糕

Bob Deblier
2019-06-20 20:39:18

Víctor Almela
2019-06-20 21:24:28

原文網址 Víctor Almela
2019-06-20 13:57:19

Hi guys,

Is possible to change printing settings in an already sliced file? I changed resin and it needs longer exposure time in bottom layers. It would be a pain to reslice all ready to print files I already have ? .

翻譯年糕

Jarrod Smith
2019-06-20 14:01:23

Stefan Giudici
2019-06-20 14:05:10

Víctor Almela
2019-06-20 14:36:37

Astartes Primaris
2019-06-20 14:38:33

Víctor Almela
2019-06-20 16:48:10

Víctor Almela
2019-06-20 16:52:40

原文網址 Víctor Almela
2019-04-04 16:05:45

Hi guys,

How do you print flat base pieces? If I do it directly without support or raft I see that some lower part of the model is lost (about 1mm), the part touching plate. If I add a raft of 1 or 2mm this doesnt happen but you get the raft printed below piece and later you need to remove/sand it.

Does slicing software apply different settings when printing piece with raft? It seems the first layers dont attach well if you print directly a flat piece.

翻譯年糕

Víctor Almela
2019-04-05 19:11:07

原文網址 Víctor Almela
2019-02-11 21:22:54

Hi guys,

Has Photon a resume print after power loss?.

翻譯年糕

Ivo Mavrodinov
2019-02-11 21:25:06