Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Richard Cooper
2019-09-30 21:58:18

Don't have a pic right now, but seeking possible (not obvious) causes of frame shearing. Models were hollowed, vented and angled. Also, does not appear to be a support issue, as they all clung tightly. Happened to 3 of 4 models on one print, even after a reprint.

翻譯年糕

Will Koehler
2019-09-30 22:31:42

Richard Cooper
2019-09-30 22:52:02

Will Koehler
2019-09-30 22:56:53

Richard Cooper
2019-09-30 23:00:30

Tiernan Messmer
2019-10-01 00:00:11

原文網址 Richard Cooper
2019-01-18 08:00:33

Hive mind, I'm having a weird problem lately with my prints, certain objects, not all are having layer shifting effectively ruining the print. I've re-sliced the models and ran the files through Validator and there is no problem that should be causing this. Just put in a ticket with Anycubic, as it's still under warranty, but has anyone else seen this before?

翻譯年糕

Evan Carothers
2019-01-18 09:21:50

Evan Carothers
2019-01-18 09:22:24

Richard Cooper
2019-01-18 09:45:08

Mark Wardle
2019-01-18 09:55:58

Richard Cooper
2019-01-18 10:25:13

Richard Cooper
2019-01-18 12:17:24

原文網址 Richard Cooper
2018-12-13 10:24:35

Anyone have an issue where the z motor quits working temporarily? I went to check a print and it was still full raised, tried to lower manually and it wouldn't respond. Fixed it with a power cycle, and it's working again, just curious if this is something to look out for in the future?

翻譯年糕

Leon Skopilianos
2018-12-13 11:04:59

Kaile Riser
2018-12-13 16:53:36

原文網址 Richard Cooper
2018-12-05 19:12:11

Anyone here have any experience with Formware 3D? (slicer program) I'm on a 30 day trial right now and I've got to say, I'm pretty impressed so far with the features!

翻譯年糕

Marcin Kudzia
2018-12-05 19:18:09

Richard Cooper
2018-12-05 19:30:07

谢信福
2018-12-05 19:41:47

Richard Cooper
2018-12-05 19:46:51

Stuart Radmore
2018-12-05 19:54:06

谢信福
2018-12-05 19:55:44

Richard Cooper
2018-12-05 19:57:59

Richard Cooper
2018-12-05 20:14:06

谢信福
2018-12-05 20:20:24

Richard Cooper
2018-12-05 20:22:36

Mathias Rosenbusch
2018-12-06 01:40:31

Mathias Rosenbusch
2018-12-06 01:45:43

Mathias Rosenbusch
2018-12-06 01:46:36

Mathias Rosenbusch
2018-12-06 01:46:47

Mathias Rosenbusch
2018-12-06 02:27:32

Muhammad Anas
2018-12-06 20:30:05

Muhammad Anas
2018-12-06 20:30:57

Stuart Radmore
2018-12-06 20:31:41

Muhammad Anas
2018-12-06 20:33:32

Richard Cooper
2018-12-06 22:30:05

原文網址 Richard Cooper
2018-11-30 00:42:10

Finally got my Photon in, from all the talk I've been worrying about how putrid the resin is going to smell and how I'm going to have to deal with the wife. Can't believe the resin smells exactly like an MRE heater, now all I am is hungry!

翻譯年糕

Frank Kincell
2018-11-30 00:43:43

Tomer Litvin
2018-11-30 00:48:41

Tomer Litvin
2018-11-30 00:48:49

Brian Morin
2018-11-30 00:52:54

Vinicius Silva
2018-11-30 00:54:55

Brian Morin
2018-11-30 00:55:52

Alexander Lew
2018-11-30 02:40:51

Nick Santana
2018-11-30 15:04:20

Richard Cooper
2018-11-30 15:14:53

Richard Riddell
2018-11-30 21:05:17

Michael J Fuller
2018-11-30 23:40:57

Nick Santana
2018-11-30 23:44:45

Richard Cooper
2018-11-30 23:46:55

Joey Pruitt
2018-11-30 23:59:50

原文網址 Richard Cooper
2018-11-29 20:12:17

Quick question, I'm planning a fairly large print; using a raft with the supports takes up almost the whole build plate, should I not do the raft or is it ok? Very new to resin printing, pretty good at FDM, though this is one of those concepts that doesn't carry over very well.

翻譯年糕

Fahrid van Uitert
2018-11-29 20:13:05