• #maker+t=market
  • COSPLAY 3D 建模
  • 3D列印服務
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Joe Kushner
2019-10-20 12:09:10

I'm getting some fierce layer shift lines. I've used a few resins but this sample below is from Using ELEGOO 3D Rapid Resin LCD UV-Curing Resin 405nm Standard Photopolymer Resin . I was told that my plate might not have been tight creating 'suction' or that my build dish might not have been tight. I checked both of those and tried a new print and had similiar results.

I was also told that I might not have enough supports so I increased the supports.

Are my settings way off? They are tilted at 45 degrees or at least are supposed to be according to Chitbox which I'm using to cut and add supports. 翻譯年糕

Robert Nisson
2019-10-20 12:15:31

Elle Heilig
2019-10-20 12:46:05

Elle Heilig
2019-10-20 12:52:03

Mikko Meriläinen
2019-10-20 15:12:14

Paul West
2019-10-20 23:38:31


原文網址 Joe Kushner
2019-10-09 22:32:23

Z wobble or ? Any recommended videoes to fix if z wobble

Straight up print with support,s not printed directly on bed. Using chitubox 64. Not hallowed.

.02 layer height

8 layer bottom count

12 exposure time

60 bottom exposure time

light off delay 0

bottom light off delay 0

bottom lift distance 5

lifting distance 5

bottom lift speed 65

lifting speed 65

retract speed 150

翻譯年糕

Stefan Sova
2019-10-09 22:34:05

Douglas Guerra Dos Santos
2019-10-09 22:37:05

Douglas Guerra Dos Santos
2019-10-09 22:37:35

Nipuna Gunarathne
2019-10-09 22:37:38

Mark Wardle
2019-10-09 22:40:17

Sandro Pateishvili
2019-10-09 22:40:35

Joe Kushner
2019-10-09 22:42:10

Mark Wardle
2019-10-09 22:42:22

Mark Wardle
2019-10-09 22:42:35

Mark Wardle
2019-10-09 22:42:59

Joe Kushner
2019-10-09 22:47:50

Joe Kushner
2019-10-09 22:48:11

Joe Kushner
2019-10-09 22:50:31

Sandro Pateishvili
2019-10-09 22:51:13

Joe Kushner
2019-10-09 22:54:26

Joshua Collins
2019-10-09 22:57:53

Mark Wardle
2019-10-09 22:59:01

Robb Nunya
2019-10-09 23:08:27

Michael Horn
2019-10-09 23:29:01

Phillip Kenney
2019-10-10 04:54:41

Ben Cox
2019-10-10 04:55:45

Ironi R Johnson
2019-10-10 04:58:55

Michael Horn
2019-10-10 04:59:56

Ben Cox
2019-10-10 05:03:32

Richard Shapiro
2019-10-10 05:37:36

Clay Whitter
2019-10-10 09:59:21


原文網址 Joe Kushner
2019-03-19 01:11:20

Where and what supplies is everyone using? Where are you ordering them from in terms of replacement? Amazon? Anycubic directly?

I had some resin in the vat and instead of cleaning it the proper way almost put my fingers through the FEP plastic film, warping the plastic.

To put in a new sheet, I see you need a hole puncher for example, more plastic, etc...

翻譯年糕

Jean-François Meloche
2019-03-19 01:12:37

Adam Green
2019-03-19 01:19:47

Adam Foster
2019-03-19 01:34:16

Richard Thomas
2019-03-19 02:51:05

Ty Mansfield
2019-03-19 02:51:35


 

討論主題

全不選 常用關鍵字